Null


Impeller movement

  • 10 Replies
  • 3106 Views

87hardin

  • Join Date: Apr 2015
  • *
  • Full Member
  • ***
  • Posts: 127
  • Karma: +0/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 0
« on: March 12, 2016, 02:34:29 PM »
Can someone tell how much play the impeller should have. On the shaft my impeller has movement back and forth side .thanks for the help seal and bearing needed replace


GT Jets

  • Join Date: Jan 2007
  • Location: Morgan Hill CA
  • *
  • Informative Member
  • *******
  • Posts: 11,752
  • Karma: +192/-0
  • Team Evil Weiner
    • View Profile
  • Liked:
  • Likes Given: 138
« Reply #1 on: March 12, 2016, 02:43:38 PM »
Front to back about .003"

Side to side will be basically the wear ring clearance.

Bowl bushing should measure out to have about .002" of clearance.

When in doubt, swap them out.

GT
  • Boat #1: 1992 Carrera 20.5 Elite (I/O bitches)
  • Boat #2: 19' Bubble deck Jet BBC Berkeley
If i get some free time tonight at work, ill play with it and post it for everyone to see.

Time to man up and yank it John!  :banghead:
Ray

87hardin

  • Join Date: Apr 2015
  • *
  • Full Member
  • ***
  • Posts: 127
  • Karma: +0/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 0
« Reply #2 on: March 12, 2016, 03:54:19 PM »
Thank you GT  I will let you know what I got

87hardin

  • Join Date: Apr 2015
  • *
  • Full Member
  • ***
  • Posts: 127
  • Karma: +0/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 0
« Reply #3 on: March 12, 2016, 07:39:52 PM »
Well i think the bowl is in bad shape, has anyone ever had luck with a sleeve  for the bearing area. Cp performance sells one.

GT Jets

  • Join Date: Jan 2007
  • Location: Morgan Hill CA
  • *
  • Informative Member
  • *******
  • Posts: 11,752
  • Karma: +192/-0
  • Team Evil Weiner
    • View Profile
  • Liked:
  • Likes Given: 138
« Reply #4 on: March 12, 2016, 08:18:04 PM »
Are the bowl bearings totally gone? If so,  the area would need to be machined before a sleeve could be installed.
  • Boat #1: 1992 Carrera 20.5 Elite (I/O bitches)
  • Boat #2: 19' Bubble deck Jet BBC Berkeley
If i get some free time tonight at work, ill play with it and post it for everyone to see.

Time to man up and yank it John!  :banghead:
Ray

87hardin

  • Join Date: Apr 2015
  • *
  • Full Member
  • ***
  • Posts: 127
  • Karma: +0/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 0
« Reply #5 on: March 13, 2016, 03:54:44 AM »
Yes, they are pretty bad. I was able to remove one bearing with my finger. With the sleeve that I saw on line, would that eliminate the use of oil in the bowl?. I know I'll have to have it machined to fit, but just wondering if im going the right way about this for long term repair. Thanks for the advice.

Brian

  • Join Date: Jun 2012
  • Location: OC
  • *
  • Newbie
  • *
  • Posts: 45
  • Karma: +2/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 3
« Reply #6 on: March 16, 2016, 09:13:32 AM »
Yes, they are pretty bad. I was able to remove one bearing with my finger. With the sleeve that I saw on line, would that eliminate the use of oil in the bowl?. I know I'll have to have it machined to fit, but just wondering if im going the right way about this for long term repair. Thanks for the advice.

Yes, going to a sleeved bearing assembly AKA shaft saver, will not allow the bowl to be an oil bath bowl bearing setup. It would then be like the old dominators where its water lubed. You will obviously no longer use the bowl seal or the bowl end cap to make all that happen.

87hardin

  • Join Date: Apr 2015
  • *
  • Full Member
  • ***
  • Posts: 127
  • Karma: +0/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 0
« Reply #7 on: March 16, 2016, 11:12:18 AM »
Is this a bad way to go trying to be a little bit conservative or should I just spend the money and buy a new bowl I mean I could if I had to but if I could save it that would be fine by me just a cruiser not a race boat thank you for your advice Brian

Brian

  • Join Date: Jun 2012
  • Location: OC
  • *
  • Newbie
  • *
  • Posts: 45
  • Karma: +2/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 3
« Reply #8 on: March 16, 2016, 11:33:40 AM »
First I'd see how a new bushing would fit in there. If you can drop it in with your fingers, then you have to make a decision. If you search hard enough, you can find used JG bowls for about what you will have in machining your bowl and buying the shaft saver kit.

steves86ta

  • Join Date: Mar 2013
  • Location: Beaumont
  • *
  • Macho Member
  • ******
  • Posts: 2,376
  • Karma: +40/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 27
« Reply #9 on: March 16, 2016, 12:09:46 PM »
you cuold always look for a goo JC bowl.
1980 Bahner 21' Mini Day
1968 Rogers project

87hardin

  • Join Date: Apr 2015
  • *
  • Full Member
  • ***
  • Posts: 127
  • Karma: +0/-0
  • Registered User
    • View Profile
  • Liked:
  • Likes Given: 0
« Reply #10 on: March 16, 2016, 12:46:37 PM »
Ok, thank you very much for your guys help. Beers on me if we ever meet up on the water. Lol

 


Website Security Test
Powered by EzPortal

Null

anything
Website Security Test