Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - bahner80

Pages: [1]
Engine Mechanical / Electrical / Re: OTH gate valve
« on: October 19, 2019, 09:55:02 AM »
Your second valve off the block is on the wrong line. Should be on tour dump line. Gate valve off the pump is essentially  a safety in case ur water lines break , clamp fail etc. and should be wide open. The gate valve off your block on the dump line is to regulate flow and try to control temp. The Bassett tee if working correctly should be normally closed at idle. It will open once thereís more pressure to overcome spring pressure. If you are fighting milky oil you can always run a line to the drivers seat with a ball valve and back to the tee to control the water manually.

Jet Pumps / Re: Drop Snoot Advice
« on: May 22, 2019, 08:21:17 AM »
Yes  the ride plate is like an extension of the pump intake that sticks past the transom ur on the rite track. On my boat I tried wedges, nozzle angle, etc.... to get it  ride a lol drier it took installing a ride plate to get the boat out the water a bit. Everything improved after that. Fuel consumption and mph.

Jet Pumps / Re: Drop Snoot Advice
« on: May 21, 2019, 10:41:02 AM »
Without a ride plate  you might feel like youíre dragging the pump and boat will ride really flat. When the boat rides flat it doesnít load the pump properly. Forgot to ask if you have a loader or not. But that will help with keep the pump loaded. There are all different  types of loader depending on hp, hull type etc.....

Jet Pumps / Re: Drop Snoot Advice
« on: May 20, 2019, 06:10:32 PM »
Do you have a ride plate? If not and youíre trying to get the most mph out of her wedge it up so the boat rides dry. Be careful of the material on the bowl where the droop is bolted itís cast aluminum and can cross thread easily and be  a bad deal. I

Boats For Sale / Re: Craigslist & ebay boats
« on: March 07, 2019, 05:07:25 PM »
Gorgeous bahner tunnel

Sent from my SM-J727T using SoCal Jet Boats mobile app
Yes it is.
This would damn near complete my bahner collection. I need this boat

Project Boats For Sale / Re: 79 Hondo Hydro
« on: July 27, 2018, 06:11:33 PM »
Thatís a sweet boat

WTB / Re: Tunnel Ram trade
« on: June 06, 2018, 08:00:07 PM »
Lol I knew what you were getting at. I build them all but prefer the Ford's!
Lmfao guess I struck a nerve.
Any self respecting Chevy owner wouldnít trade down.
Carry on

WTB / Re: Tunnel Ram trade
« on: June 05, 2018, 08:34:58 PM »
Itís a ford Chevy rivalry I guess. Just being

Projects / Re: Southwind resurrection
« on: May 11, 2018, 07:30:39 PM »
Try jb hiperformance they sell a bunch of parts used an new I found them on Instagram

Depends on if itís  a lite lay up to support the bow. If ur looking to get some mph out of her Iíd suggest it.

Boat Showcase / Re: Southwind resurrection
« on: April 26, 2018, 11:01:25 AM »
You have scored my friend

Boat Showcase / Re: Lets See Your Rides
« on: August 07, 2017, 08:04:51 AM »
Tow rig and our daily

Engine Mechanical / Electrical / Re: Gate valve routing
« on: June 22, 2017, 09:42:52 AM »
Lol hahahaha, x2, you've just hit the daily double

The No Wake Zone / Re: What did you do to your boat today?
« on: November 30, 2016, 04:05:14 PM »
Picked up  this long awaited rail kit from lightining  today

WarZone / Re: Looking for a jet!
« on: September 02, 2016, 04:20:48 AM »
Haha guess I struck a nerve, just my opinion  trying to save you some heartache  building that olds. But do what you want.  If you couldn't  maintain shevie,  good luck maintaining a jet  boat. Don't let  a woman blind you from a logical decision but it's ur $. Good luck on shore with ur olds as I skate past you in my chevy

The No Wake Zone / Re: I want to see tow riggs
« on: July 15, 2016, 06:28:49 PM »
Here's my wife's grocery getter/tow rig 8mpg round town ,12 towing our bahner to river

Pages: [1]

Website Security Test
Powered by EzPortal


Website Security Test