Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - angermgmt

Pages: [1] 2 3 ... 18
1
Engine Mechanical / Electrical / Re: Is this normal?
« on: October 27, 2018, 11:05:35 AM »
My Offy is designed that way. All good.


Sent from my iPhone using SoCal Jet Boats

2
Engine Mechanical / Electrical / Re: Swapping 454 to 460
« on: October 22, 2018, 02:52:47 PM »
Different


Sent from my iPhone using SoCal Jet Boats

3
Engine Mechanical / Electrical / Re: Question?
« on: October 18, 2018, 08:44:29 AM »
Put a thin layer of black silicone around all the water jackets on the block under the head gasket and again on the top of the head gasket so it seats well to the head surface.  Also on the water jackets on the head where it mates to the intake


Sent from my iPhone using SoCal Jet Boats

4
You could have had a rocker arm out of torque.


Sent from my iPhone using SoCal Jet Boats

5
I doubt itís a main bearing issue. Summit sells valve spring tension tools. Might be worth the investment of your lifters all look good


Sent from my iPhone using SoCal Jet Boats

6
Whenís the last time you adjusted your valves ?


Sent from my iPhone using SoCal Jet Boats

7
WarZone / Re: Buying a used boat
« on: August 07, 2018, 08:27:46 AM »
Run it on the water before you buy it.


Sent from my iPhone using SoCal Jet Boats

8
Jet Pumps / Re: What do you use?
« on: July 27, 2018, 01:06:02 PM »
If it were me I would dismantle that transom plate and re evaluate.


Sent from my iPhone using SoCal Jet Boats

9
Interior / Re: Need a carpet guy
« on: July 26, 2018, 09:38:00 AM »
Is your old carpet in one piece?  If so why not just use it as a pattern, dry fit it and then start glueing.


Sent from my iPhone using SoCal Jet Boats

10
Engine Mechanical / Electrical / Re: BBF Canton pan set up
« on: July 25, 2018, 10:57:12 AM »
Itís similar. My pick up mounting surface is on an angle. Looks like youíll be fine with the matching components .


Sent from my iPhone using SoCal Jet Boats

11
Engine Mechanical / Electrical / Re: BBF Canton pan set up
« on: July 25, 2018, 07:51:55 AM »
Also I didnít use the pick up supplied with the kit of course...


Sent from my iPhone using SoCal Jet Boats

12
Engine Mechanical / Electrical / Re: BBF Canton pan set up
« on: July 25, 2018, 07:50:23 AM »
You just need to match it up with your pick up tube. I had to use this one in order to duplicate and match my rear pick up https://www.summitracing.com/parts/mel-m84bhvs.


Sent from my iPhone using SoCal Jet Boats

13
Gelcoat / Paint / Fireberglass Repair / Re: How bad?
« on: July 24, 2018, 03:05:01 PM »
Im not an expert but it looks like you need to do some glass work.


Sent from my iPhone using SoCal Jet Boats

14
X2


Sent from my iPhone using SoCal Jet Boats

15
Engine Mechanical / Electrical / Re: White paste on dipstick
« on: July 17, 2018, 04:22:26 PM »
It connects from the pump to your inlet line(s)


Sent from my iPhone using SoCal Jet Boats

16
The No Wake Zone / Re: New shinny stuf
« on: July 14, 2018, 01:48:09 PM »
Hook a vacuumed gauge up before you switch and check the reading with your 850 at WOT. If itís close to zero then the two 660ís may be overkill.


Sent from my iPhone using SoCal Jet Boats

17
WTB / Re: Tunnel Ram trade
« on: June 06, 2018, 09:49:02 AM »



Sent from my iPhone using SoCal Jet Boats

18
Boat Showcase / Re: Ready for the season.
« on: April 29, 2018, 05:08:27 PM »
Thanks brother. It is what it is...  should be up and running in several weeks.


Sent from my iPhone using SoCal Jet Boats

19
Boat Showcase / Re: Ready for the season.
« on: April 29, 2018, 12:44:22 PM »
Sad news, lifter froze destroyed  the cam. Block goes to machine shop tomorrow. Hopefully back up and running in a few weeks. Irony is she was still purring. Only heard the tick putting it on the trailer. ☹️


Sent from my iPhone using SoCal Jet Boats

20
Boat Showcase / Re: First Jet Boat 79 Shark
« on: April 28, 2018, 06:28:24 AM »
Nice!


Sent from my iPhone using SoCal Jet Boats

21
Projects / Re: 1975 challenger build
« on: April 23, 2018, 11:42:28 AM »
Great job and quick work. Someoneís motivated.


Sent from my iPhone using SoCal Jet Boats

22
Hulls / Re: Open the huge can of worms
« on: April 23, 2018, 08:27:57 AM »
Great job. That should last a very long time.


Sent from my iPhone using SoCal Jet Boats

23
Videos (SCJB.tv) / Re: Storage Solution
« on: April 23, 2018, 06:46:18 AM »
No room for error there.


Sent from my iPhone using SoCal Jet Boats

24
Engine Mechanical / Electrical / Re: 76 eliminator set up
« on: April 21, 2018, 02:14:10 PM »
Looks like your thermostat housing has a plug where you can install your gauge as well.


Sent from my iPhone using SoCal Jet Boats

25
Engine Mechanical / Electrical / Re: 76 eliminator set up
« on: April 20, 2018, 07:43:37 PM »
Before you invest in a bigger carb test the one you have with a vacuumed gauge attached to your intake. If the pressure is near zero at WOT then an 850 is not necessary IMO. There should be a couple different spots on your intake you can attach a pressure gauge to a water passage. No need to drill and tap. Here is where I have mine. As yes a gauge that says fuel will work.


Sent from my iPhone using SoCal Jet Boats mobile app

Pages: [1] 2 3 ... 18

Website Security Test
Powered by EzPortal

Website Security Test