Null

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bigblock92557

Pages: [1] 2
1
WTB / wtb bbc motor
« on: March 01, 2010, 09:18:41 PM »
looking for a fresh BBC................. :banghead: four bolt main.....summer is around the corner

2
Random Boat Parts For Sale / Re: Anyone want to experiment?????
« on: August 20, 2009, 06:35:22 AM »
Yeah GT... my neighbor has this on his camaro 427cid and he swears by it... but thanks.

3
Random Boat Parts For Sale / Anyone want to experiment?????
« on: August 19, 2009, 09:29:24 PM »
Hi guys,
I have a brand new in a box Stage 2 Boost/Cooler water/methanol injection system from snow performance. I was planning to to try this myself but my power plant went to junk....  :banghead: For those who are curious what this is here is the link to the actual kit http://www.snowperformance.net/product.php?pk=77 the one I got has the two plate for two carbs for a tunnel ram I also have 3 cases of BOOST JUICE to go with it.With this kit you could Run 11:1 to 13:1 compression ratio (or more) on pump gas!! Increase your pump gas octane by 20-25 points and make more power. More power and efficiency with cooler running for your naturally aspirated V8 Muscle Engines.


This kit uses a progressive controller that proportionally injects more or less according to manifold vacuum. Start and full points are adjustable for engagement and delivery curve, to match what the engine requires. High compression modified engines can gain performance through cooler intake charges and the large increase in octane and detonation suppression. It can also be geared towards fuel economy and using lower grades of gasoline. Comes with one or two 4150-style 1" Carburetor spacer plate(s) or a Dominator carburetor spacer plate threaded for Snow Performance injection nozzles, and a solenoid to prevent vacuum siphoning.

If anyone is intrested just PM me or email me csanchez92557@gmail.com I paid close to 800 dollars for the kit and the juice Im asking 350 for it all and to add to all this I just want to give The EngineDoctor AKA David from A & D Engine a huge thank you for your help and advice, it is greatly appreciated. This forum & the people are gr8t!!!!!!


4
The No Wake Zone / Re: What do you do for a living??
« on: August 18, 2009, 06:31:10 AM »
Im a PLC Programmer/Electrical Technician..... :screwy: for Kraft Foods the plant im in make Lunchables in Fullerton,Ca

5
WTB / NEED 4 BOLT MAIN CAPS BBC
« on: August 11, 2009, 06:31:06 PM »
Hey guys I need some 4 bolt main caps used or new. Email me csanchez92557@gmail.com please help!!!!!!!  :banghead:

6
WTB / BBC top mount hight torque stater
« on: July 20, 2009, 06:34:31 AM »
Hey guys,

Looking for a top mount high torque starter for a big block chevy , PM me or email me
csanchez92557@gmail.com thanks

7
Lake Havasu / Anyone going out to Havasu this weekend?
« on: July 14, 2009, 11:30:27 AM »
Hey guys
Anyone going out to Havasu this weekend? I like to meet some of you guys and share a few cold one's im meeting a couple of oldtimers by the sandbar on saturday and make our way up to Moabi Park.

8
Engines / Engine Parts For Sale / Re: BBC Plumbing
« on: July 14, 2009, 11:25:30 AM »
I can look for my old one but I just bought them at ACE Hardware but I changed them to 8 AN fitting what is it that you need a barbed fitting or a AN fitting.

9
Engines / Engine Parts For Sale / Re: BBC Plumbing
« on: July 14, 2009, 11:05:27 AM »
?????? Hose fittings or block plate w/NPT threads??????

10
The No Wake Zone / Re: so cal hats........
« on: July 14, 2009, 07:07:34 AM »
Hats would be BAD AZZZZZ......but where or how can i get some stickers for my boat and truck???
Anyone know?  :sly:

11
Engine Mechanical / Electrical / Re: Ignition protection....?
« on: July 09, 2009, 06:51:11 AM »
All my grounds are good but I found the root of the cause, it was the altenator.. :banghead: took it down to autozone to test sure enough over charging and thanks for that link on that CHARGE GUARD i ordered one last night so i should be good to go for this weekend  :thumbup:thanks guys, very very helpful  ;D

12
Engine Mechanical / Electrical / Re: Harness breaker?
« on: July 09, 2009, 06:06:59 AM »
Well
I installed another breaker for the stereo system (100amp) with its own lead from the battery, So the only other thing thats left are my gauges,Alt.....e.t.c.. how about isolating the alternator on it own breaker, maybe two 30's or one 30 for the alt and one 15 for the console.

13
Engine Mechanical / Electrical / Re: Harness breaker?
« on: July 08, 2009, 09:17:16 PM »
Comprendo what your saying im just rewiring the boat and the breaker is very brittle and i cant read anything on it as far as the wire gauge looks like a 10  thanks

14
Engine Mechanical / Electrical / Harness breaker?
« on: July 08, 2009, 08:57:33 PM »
Another question guys anyone know what size of breaker that is on the 12 volt feed to the terminal or the breaker that feeds the entire boat?

15
Engine Mechanical / Electrical / Ignition protection....?
« on: July 08, 2009, 02:38:23 PM »
So here it is guys, I have a Mallory series 50 Magnetic Breakless Igniton now i was on my way back to windsor ramp Sunday morning after the 4th and about 400 ft. or so the boat died, no crank no nothing so i checked my breaker and bingo it was popped, now upon reseting it  the engine would turn but no start so i figured i got no spark now after taking her back to the trailer i verify and sure no spark well the ignition module inside went out so i made the stupid mistake of buying another module on Monday without checking for a  short to ground possibly so i installed, ran a test and start the engine, now the boat starts runs for 10 to 15 second and senario all over again breaker main pops.... :banghead: I run my module test to see if it was ok only to find out that i f@#$%@&* it up again  :mad: I know i have to look for a short somewhere  but my question is, is there a way to protect the module i think  a fuse on the hot going to the module would'nt help since it would still get that spike before it would blow, maybe possibly a zener from the hot going in to the negative going to the engine block or a (MOV)Metal Oxide Varistor in place of the zener has any of you guys had this issue and all im trying to accomplish is protecting that module for me and anyone and save myself those $83 dollars not to mention that it could ruin your weekend since it's not your everyday autozone part....  :banghead:

16
Engine Mechanical / Electrical / Re: header water lines
« on: July 08, 2009, 02:11:19 PM »
Headers sold thankz

17
WTB / Re: bassett water lines and T valve
« on: July 07, 2009, 11:58:23 AM »
He needs the Twisty style and there for a Big Block Chevy

18
Random Boat Parts For Sale / BBC SHORT BASSETT HEADERS
« on: July 06, 2009, 02:04:31 PM »
I GOT A SET OF BBC BASSETT HEADER I DONT HAVE THE TEE OR WATER LINES BUT THERE IN PRETTY GOOD CONDITION NO HOLES ASKING $250.00 FOR THEM..THANKS GUYS

19
Depends if you want them new or used? I belive there's a guy on craigslist in las vegas selling some which is the link below...
http://lasvegas.craigslist.org/boa/1203462670.html

and if you want them brand new you might want to try directly from Bassett in  Anaheim, California
there pretty cool ask for James,Mike or Paul they will answer any question you have, a new set will cost you $1196.25 and thats including tax....I know I just bought some  ;D any way's heres there number
1-800-345-5824

Also keep in mind that if later you find some used ones and they dont have the water lines or tee they will cost you a ridicouls  :banghead: amount of money $196.00 for the water line and $85.00 for a tee from a shop or from Bassett. :screwy:

20
I think thats what read on the timing chart any who  :sly: here a link to the timing chart or cam card if anyone cares....
http://iskycams.com/timingchart.php?product_number=390288

21
 Thats funnie there RV Cam huh  :mad: ok well I guess theres only one way to find out huh......I just thought 98 degree overlap was alot  ::) thanks so much for info guys  :thumbup:

22
Ok guys'
Heres my delima I have a set of Bassett thru the transom headers now tips are just under the water line, I have a 89 commander my question is I have a z-88 ISKY cam it has a 272 duration both intake and exhaust at .50 thousands with 108 center lobe my tip's have flappers in them would i have a problem with it sucking water back in with that big of a riser bent into the pipes? I tried putting a set of over the transom but it did'nt clear the pipes did'nt clear the transom all this is making me go  :screwy: and i just keep  :banghead: any help or advice would be gr8tly appreciated.

23
WTB / Re: looking for b cut impeller
« on: June 30, 2009, 06:13:16 AM »
I have a B Aggressor aluminum impellar just sitting in my garage with minor knicks on the fins but a good file should take care of that your more than welcome to have it.

24
Lake Havasu / Re: WTF?????
« on: June 22, 2009, 06:21:30 AM »
Hey Guys im fairly new to this site, but i was out there since memorial weekend to this past weekend and it was alot worse than this past weekend but heres a link where you can read all about it..... and yes its f#$@#$% gross


http://www.havasunews.com/articles/2009/06/18/news/doc4a39c9dd14878279759970.txt


25
Random Boat Parts For Sale / Re: garage sale
« on: June 19, 2009, 12:11:43 PM »
Im  looking for a front engine mount for BBC & a set of water lines for bassett headers

csanchez92557@gmail.com

Pages: [1] 2

Null

SMFPacks CMS 1.0.3 © 2020