Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - RTriebess

Pages: [1]
1
Boats For Sale / 1979 Youngblood TX-19
« on: August 04, 2010, 03:57:42 PM »
1979 TX-19 BLOWN 540 ASKING 18K
(916)473-3753 RYAN
DART BLOCK, AFR HEADS, SOLID ROLLER CAM, 871 BLOWER, DEMON 850 CARBS
DOMINATOR PUMP HI-HELIX IMPELLER DROOP RIFE PLATE BACK CUT SHOUE
WILL TRADE FOR V-DRIVE WAKEBOARD BOAT OR 1967-69 CAMARO

2
Gelcoat / Paint / Fireberglass Repair / how to spray gel coat
« on: March 12, 2010, 05:25:22 PM »
Do you thin it before you spray if so what ratio? Thanks

3
Engine Mechanical / Electrical / WTB gauges for sale
« on: February 09, 2010, 11:42:25 PM »
I'm looking for gauges All black faces and rings tack 3 1/2 alt, fuel, water, oil, vac/boost 2 1/16. The only ones i've found that I like are for cars. How long will they last in comparison to marine?

4
Engines / Engine Parts For Sale / wtb intercooler
« on: February 01, 2010, 08:20:48 PM »
intercooler for an 8-71 anybody have one for sale

5
Gelcoat / Paint / Fireberglass Repair / 19 daytona rounded keel pics
« on: November 29, 2009, 04:47:49 PM »
Can someone put some pics of a rounded keel daytona up so I can see please.

6
Hulls / daytona rock climber project
« on: November 27, 2009, 03:38:01 PM »
Starting the rock climber project pictures  to come. Have about five holes in the bottom of the boat ranging from 5-10 inches big. The bottom of the boat is a delta bottom and was wondering if I should convert it to a rounded since there is so much bottom work to be done anyways?  Should I set the pump back. It will be a drag boat.

7
Engines / Engine Parts For Sale / blower injection setup
« on: September 19, 2009, 03:29:14 PM »
Looking for complete injection setup.

8
Engines / Engine Parts For Sale / Demon 850 blower carbs
« on: September 19, 2009, 03:26:37 PM »
Everything you need to run. $1500 brand new used 1 summer. hat, carbs, linkage, blower top, and hard fuel lines. Will trade for injection setup.

9
Hulls / best way to fix a hook
« on: September 19, 2009, 02:26:08 PM »
Looking for the best way to fix a hook in the bottom of the boat.

10
Hulls / Need ideas on how to air out my boat
« on: September 13, 2009, 12:22:47 PM »
I have seen some pics of some other tx-19 that are running very dry. I'm stuck in the water right now at the front of my motor. I have a droop and a ride plate. Ride plate is up about 4 deg. in comparison to the bottom of the boat. Berk droop with place diverter.

11
Jet Pumps / ultimate wear ring
« on: September 11, 2009, 08:12:38 PM »
has anyone seen the orange ultimate wear ring. are they worth it?

12
Engine Mechanical / Electrical / engine lays over at 5k rpms
« on: July 05, 2009, 01:37:44 PM »
well I have been fighting the tune on my motor all year. I have been jetting the heck out of it all over the board to find out that my dist. was broken and advance that i thought was locked out wasn't intermitently. got that fixed and it now is running ok I can actualy drive around the lake now.

blown 540 afr 345 heads deamon 850 blower carbs 716 solid roller cam 5lbs of boost
88 jets in primarys 96 in sec boost ref power valves (4.5) timming locked at 28 deg.
37 squirters primary 31 sec. no intercooler
symptoms: pops through carbs sometimes when i punch it like a lean pop and at 5000 rpms it lays over like it is out of gas and if you stay in it it comes and goes it will start excellerating again then lay over then excell again.seams like when it starts making boost is when it starts to lay over.

fuel system:aeromotive a1000 with there filter and bypass reg. 7lbs of fuel psi all the time. have the hard line fuel kit on the carbs
 
any ideas. to little jet? not enough timing? to much jet? Have went down to 82 prim 85 sec jettting and it would lean pop bad
went back to the 88-96. The plugs are black as if it was rich but it pops like it is lean.


13
Jet Pumps / tap location for suction housing psi
« on: May 04, 2009, 10:25:48 PM »
were do you tap at what psi should I see.

14
WTB / blower carbs
« on: February 23, 2009, 02:12:46 PM »
looking for two blower carbs holley 950 cfm or demons or what do you have
need fuel lines and linkage also
Ryan (916)473-3753

15
WTB / stainless steel impeller
« on: February 23, 2009, 02:02:31 PM »
a or aa for dominator pump.
Ryan (916)473-3753

16
WTB / chevy big block heads
« on: February 23, 2009, 02:01:25 PM »
looking for a set of dart pro 1 or afr 345 heads or equivalent 345cc intake runners 119cc chambers

Ryan (916)473-3753

17
Boats For Sale / 1979 Youngblood TX-19
« on: July 13, 2008, 09:56:30 AM »
!979 Youngblood tx-19 with a chevy 454 duel tunnel ram with 600 holleys. Dominator pump set back with droop shoe and ride plate. manual place diverter. Ryan (916)474-4250 (916)473-3753 Will try to get pictures up as soon as i find my cable to download them. $12K

18
WTB / BERK DROOP
« on: January 26, 2008, 04:24:50 PM »
LOOKING FOR A BERK DROOP

19
The No Wake Zone / used part pricing
« on: January 20, 2008, 12:11:12 PM »
I can't help but make a post on the prices I see for some of the used parts for sale on this site. It seems like people want there weight in gold.  I've bought used basset headers in brand new condition and motor mounts for a big block chevy all for $350. A set of basset ford big block headers for $150 in very good unburnt condition, dooley oil pan with windage tray for $50 for the ford. Buyers beware ther are deals out there.

20
WTB / Big block chevy oil pan for jet
« on: January 18, 2008, 01:44:24 PM »
Looking for big block chevy oil pan for a jet boat. Thanks Ryan

21
Project Boats For Sale / 1975 Hondo V-drive
« on: January 14, 2008, 12:57:09 PM »
1975 hondo v-drive set up for big block chevy. comes with oil pan pickup and pump, timming cover and water pump, headers twisties, motor mounts, has spring kit on cav plate. Ryan (916)992-0313
$3000 obo...

22
WTB / berkeley intake
« on: January 14, 2008, 12:41:25 PM »
looking for a berkeley intake Ryan(916)992-0313

23
Projects / 79 youngblood pump set back
« on: January 06, 2008, 05:51:37 PM »
Im getting ready to set the domminator back in my tx-19 and was wondering how far I should set it back anyhelp would be good.

24
WTB / 1975 Hondo V-Drive Boat
« on: December 09, 2007, 04:24:19 PM »
1975 Hondo V-Drive $2500 Excellent Condition. Ryan  (916)473-3753 or (916) 992-0313 Got to link below for Pictures

http://sacramento.craigslist.org/boa/498061413.html

Pages: [1]

Website Security Test
Powered by EzPortal

Null

Website Security Test