Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - lbhsbz

Pages: [1] 2 3 ... 61
1
Project Boats For Sale / Re: Bahner tunnel project
« on: April 05, 2018, 07:10:57 PM »
Good, that means itís your turn now.   When should I expect you?

2
Project Boats For Sale / Re: Bahner tunnel project
« on: April 04, 2018, 11:32:18 PM »
I can't believe I still have this thing...anybody?   

Does anyone have a worn out pump for sale with an intake?...the kid wants a "fast boat with chrome mufflers"...so I might build it, even though the wacker will be way better.

3
Project Boats For Sale / Re: Bahner tunnel project
« on: March 24, 2018, 09:43:48 AM »
Not a lot of bahner tunnels out there I was thinking converting it to a jet
I figured that would be its next life...thatís why I posted it here

4
Project Boats For Sale / Re: Bahner tunnel project
« on: March 24, 2018, 09:42:58 AM »
Where you located Iam in the San Fernando valley


Sent from my iPhone using SoCal Jet Boats
Located in Long Beach

5
Project Boats For Sale / Re: Bahner tunnel project
« on: March 23, 2018, 11:54:24 PM »
Is it a full stringer boat


Sent from my iPhone using SoCal Jet Boats

yup.  2x4 stringers

6
Project Boats For Sale / Re: Bahner tunnel project
« on: March 23, 2018, 11:02:33 AM »
Bought a new boat.  It runs fine, but this motor is going on the new boat. 

I have a real nice 1988 XR-4 150hp merc...unmolested with a brand new lower unit that could go with the boat...but I need to get $2K for that motor...so, $3K running and ready to go...you'll just have to deal with shitty interior and shitty gel, but otherwise it would be ready to run.

Give me a call if you want to chat about it.

7
Project Boats For Sale / Re: Bahner tunnel project
« on: March 23, 2018, 08:16:57 AM »
Trailer goes with it

8
Outboards / Re: Outboard help
« on: March 23, 2018, 12:26:41 AM »
been good....tried calling you a while back.   PM me a phone number...we need to catch up.   Hope things are good on yer end.

9
Project Boats For Sale / Bahner tunnel project
« on: March 22, 2018, 10:19:19 PM »
Currently rigged for an outboard, but being sold without power.

Hull is solid.   Gel is shot and needs interior.   $1000


10
Outboards / Re: Outboard help
« on: March 22, 2018, 10:12:19 PM »
You have a chrome bore 2.4L, so there's not a whole hell of a lot you can do to it to make more power before things start getting stupid expensive.   

If it's running well and your compression is decent (120ish psi) it's healthy and if it's on the boat in your avitar, I'd leave it alone.  The best upgrade you can do is a set of fiberglass reeds from Chris Carson Marine Service, and if you're in the mood for premium fuel or even mixing AV gas, mill the heads to get the compression up a bit.  Chris Carson also sells reed spacers to stuff the crankcase a bit more now too.   

What are your current speeds?   How is the boat mainly used?   What are your goals for the boat?

11
bump

sitting on the couch...wishing I was sitting elsewhere...

never gets old

12
The No Wake Zone / Re: Ray Black
« on: June 30, 2017, 06:35:30 PM »
Saw that too.   Sucks.   He was one of the good ones.

13
Jet Pumps / Re: Leaking jet
« on: June 24, 2016, 07:15:54 PM »
You have the bowl off, throw new bushings in it and a new seal.   How's the tail end of the shaft look?

14
The No Wake Zone / Re: Foward and reverse bucket.....
« on: June 15, 2016, 07:50:35 PM »
There should be a wave washer on the shifter axle that provides friction to keep it in place...might be missing?   

15
Outboards / Re: Bnag
« on: May 07, 2016, 09:30:22 AM »
New powerhead is on and running....never had a motor with over 90psi compression before, let alone 115-120psi.   It should run good

16
Outboards / Re: Bnag
« on: May 07, 2016, 09:19:34 AM »
I think we'll call it dead

17
Outboards / Re: Need to find a 300, 350, or 400 outboard motor
« on: May 06, 2016, 07:24:01 PM »
Hmmm.   Something is strange about that craigslist engine.   The cowl logo looks like it's from a '90 and later, but it has the early 2 piece heads.   I take silencer looks more like a 135 piece.   Check the serial number on the freeze plug behind the flywheel to see what it really is before buying it.

18
Outboards / Re: Need to find a 300, 350, or 400 outboard motor
« on: May 03, 2016, 10:41:07 PM »
Too much weight.  Look for a Merc 2.5L

19
The No Wake Zone / Re: Drilling holes for exhaust tips....How?
« on: April 01, 2016, 07:58:55 PM »
Drill your pilot hole, then start the whole saw backwards to get a score in the gel so it doesn't chip

20
Sold

21
Outboards / Re: Bnag
« on: March 23, 2016, 09:35:24 PM »
That's the plan

22
Outboards / Bnag
« on: March 23, 2016, 09:06:24 PM »
Pulled the heads off to have a looksee...


23

This one?


Sent from my iPhone using SoCal Jet Boats

Winnar!

24
The No Wake Zone / That picture of Crewchief passed out in his boat
« on: March 09, 2016, 10:46:55 PM »
If you can find it and post it, it'll buy you a beer at Big River.  I've tried to find it, I give up.  this is important.  please help. 

It's the one with his feet propped up over the passenger side gunnel....most likely after too much apple pie in a jar

25
Boats For Sale / Re: Anybody on the hunt for a killer fishing boat?
« on: March 04, 2016, 07:28:33 PM »
So...do you have the pretty green Bimini an you'r missing the full canvas or is there no canvas

Pages: [1] 2 3 ... 61

Website Security Test
Powered by EzPortal

Website Security Test