Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Pisscan

Pages: [1]
Boats For Sale / Re: 1970 rogers/Weiman
« on: November 05, 2018, 08:40:30 PM »
Full Stringers or 3/4 .

Sent from my SM-G930W8 using SoCal Jet Boats mobile app

Hulls / Stringers and floors
« on: October 27, 2018, 10:53:07 PM »
 I have this Weimens boat.I really want to go with no floors . Looks like someone had replaced the floor front of the engine bay . I remove the rotted floor from around the bay .Now I can tell it does not have full stringers perhaps 3/4? Question is are Roger's boats with full stringers the only ones that you can do away with the floor?

Sent from my SM-G930W8 using SoCal Jet Boats mobile app

Jet Pumps / Re: Dominator jet 12s issuies
« on: October 21, 2018, 04:52:53 PM »
1. Looks like the old style. Water lubed bushings and smaller exit opening would determine the early style.

2. I used a large pry bar in the u-joints up against the stringers to hold the shaft from turning.

3. From that pic, you cannot yet see the wear ring. Needs to come apart.

4. Better to check 'play' with the bowl on, thru the clean out access hole.

So I cut the nut, cut the shaft and guess what that impeller was not a coming off! All ok I was planning on a complete build of the pump anyhow.

Sent from my SM-G930W8 using SoCal Jet Boats mobile app

Jet Pumps / Dominator jet 12s issuies
« on: October 15, 2018, 04:25:14 PM »
I am new to this jet world hoping someone2 can shed some light, 1st in my photos is this bowl the new or old type, 2nd I can not get that impeller but off ! 3rd looking at the wear ring the best i can it show heavy scaring. 4th there is some play in the shaft I would think there would always be some but the bushing in the bowl keeps everything a ok? I welcome any thoughts on what happened and how to get this nut off.

Sent from my SM-G930W8 using SoCal Jet Boats mobile app

Hulls / Re: 1975 Anthony
« on: September 29, 2018, 02:44:35 PM »

Hulls / Weimens Stringers
« on: September 23, 2018, 07:21:06 PM »

Jet Pumps / Re: Thrust Bearing failing?
« on: September 16, 2018, 12:26:03 PM »
Thanks for the reply, l feel better knowing it might be the wear ring. I bought this bought a couple months ago , I just run the engine to fire it up after carb adjust nothing longer that a min .

Sent from my SM-G930W8 using SoCal Jet Boats mobile app

Jet Pumps / Thrust Bearing failing?
« on: September 15, 2018, 09:54:22 PM »
I have a Dominator 12 s and  the  new to the jet boat world. When running the jet out of the water and a water hose hooked up for cooling at times I get a very loud scream goes away but comes back at times.This  seems to come from the thrust bearing area hard to tell as it's so loud. When I run this Weimans boat never a noise but I seem to keep thinking I am going to have some major problems if I dont catch what's wrong. PS the bearing housing does not get hot. How can I check this bearing out ?

Sent from my SM-G930W8 using SoCal Jet Boats mobile app

Jet Pumps / Dominator Jet Drive no power
« on: September 11, 2018, 08:33:55 PM »
I picked up a Rogers boat with a Dominator pump, for now its running a SBC rebuilt flat top pistons etc. My 1st few times out it was running fine loads of power hi some hard water and things slowed down lost power, rebuilt the carb, check the grate and clean out. Seems to me if my wear ring needed replacing I have hi refs, is there a chance my thrust bearing is seizing up its not getting hot. The pump just seems to be holding back . The engine runs fine just lower RPM. Can anyone help as I ma stump on what to look for ...

Pages: [1]

SMFPacks CMS 1.0.3 © 2020