This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - el mojado
1
« on: October 17, 2018, 09:43:23 PM »
Why not just get rid of the Facebook group altogether? Seems like it has brought nothing but grief. Can we vote on it? I liked the feeling of being part of something so small yet felt so big. SCJB.com is awesome!!! Sent from my SM-G950U using SoCal Jet Boats mobile app
2
« on: October 16, 2018, 11:49:49 PM »
When docking, I finally learned that you use the FOR/REV lever to control speed. Step on throttle just off idle and use the lever to ease into where you are trying to get the boat to go. Wanna go slow, less forward. It takes a little practice, but I found this method to give me better control than blipping the go pedal and swinging the steering wheel left and right. Hope this helps. Good luck..... BTW, I learned this from someone's recommendation on this forum Sent from my SM-G950U using SoCal Jet Boats mobile app
6
« on: September 25, 2018, 08:37:55 AM »
I have a box style anchor. How long rope do you guys use? I boat at the river and Havasu. Does it need to have a chain? Sent from my SM-G950U using SoCal Jet Boats mobile app
8
« on: September 17, 2018, 02:47:49 PM »
If you still have them I’ll give you $50 for them
Sent from my iPhone using SoCal Jet Boats
Yes. I still have them Sent from my SM-G950U using SoCal Jet Boats mobile app
11
« on: September 02, 2018, 10:19:58 AM »
12
« on: August 31, 2018, 09:35:50 PM »
Damn it.... I don't have that bell housing. Thank you though Sent from my SM-G950U using SoCal Jet Boats mobile app
13
« on: August 31, 2018, 06:02:35 PM »
Looking for 4 bolt main BBC bare block. Text at 626 483 2062..... Robert. Thanks guys..... .040 or less.
Sent from my SM-G950U using SoCal Jet Boats mobile app
2 piece rear main MARK IV Sent from my SM-G950U using SoCal Jet Boats mobile app
14
« on: August 31, 2018, 06:00:29 PM »
Looking for 4 bolt main BBC bare block. Text at 626 483 2062..... Robert. Thanks guys..... .040 or less. Sent from my SM-G950U using SoCal Jet Boats mobile app
15
« on: August 27, 2018, 11:22:07 PM »
Looks like a very doable project. Its a sickness Sent from my SM-G950U using SoCal Jet Boats mobile app
16
« on: August 18, 2018, 09:14:16 AM »
I paid a shop about 400 dollars to have 2 "S" pipes made out of stainless. My snails were way off alignment to the exhaust tips. Sent from my SM-G950U using SoCal Jet Boats mobile app
17
« on: June 14, 2018, 08:15:00 AM »
18
« on: June 05, 2018, 07:42:55 AM »
Removing that rear single bolt will do nothing to separate bowl. Those 8 bolts on the inside gotta be removed to separate the bowl. There might be silicone holding it together. Sent from my SM-G950U using SoCal Jet Boats mobile app
19
« on: June 01, 2018, 09:31:00 PM »
If I can rebuild it, anyone can rebuild it! (with a little over the phone coaching from Mash On It) Sent from my SM-G950U using SoCal Jet Boats mobile app
20
« on: June 01, 2018, 09:27:38 PM »
Let me know if you want to sell the WJ diverter Sent from my SM-G950U using SoCal Jet Boats mobile app
21
« on: June 01, 2018, 07:34:41 PM »
If it had a weight, new one must also have a weight. If it had no weight, new one must not have a weight. The holes will be there regardless. The holes are where the weight is mounted. I just went through this. Sent from my SM-G950U using SoCal Jet Boats mobile app
23
« on: May 07, 2018, 12:47:12 AM »
I figured out that I had an internally balanced set up. Installed correct balancer and flexplate and vibration is gone Sent from my SM-G950U using SoCal Jet Boats mobile app
24
« on: April 29, 2018, 09:23:06 PM »
Would I be ok running a stock 454 balancer for a full roller 496? I fired up my engine and it had a bad vibration. I removed the balancer and noticed it had no weight in it. Which balancer is good to run? Do I NEED SFI in a cruiser? Sent from my SM-G950U using SoCal Jet Boats mobile app
|
Show Posts
