SoCal Jet Boats
Tech Talk => Engine Mechanical / Electrical => Topic started by: Jetboat949 on March 15, 2017, 09:12:00 AM
-
This might be a wildly stupid question but what kind of grease should I use for a jet pump? I'm guessing marine but I'm not sure if there's some other special kind? Thanks! 😂
Matt
Who farted?
-
A grease that's rated for high temp and water should work, but ny grease is better than nothing.
Sent from my iPhone using SoCal Jet Boats
-
Lucas Red and Tacky Home Depot), Amsoil Marine Synthetic (me), Chevron waterproof Synthetic (Grainger), Aqua Lube (absolute mother fugger to clean up).......
All work great. You're looking for lithium based.
Sent from my SM-G900V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)
-
.
-
Is there a reason not to use 90 weight gear oil in my Berkeley's eye holes? That's all the pump had known for 40 years...
1976 and 1977 Challengers
-
Is there a reason not to use 90 weight gear oil in my Berkeley's eye holes? That's all the pump had known for 40 years...
1976 and 1977 Challengers
Berkeley bowl bearings do best in oil.
The grease being talked about is for the thrust bearing....
Sent from my SM-G900V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)
-
Gotcha sorry I misunderstood. I have heard of people replacing the plugs with zirks and I never understood that. thanks GT
1976 and 1977 Challengers
-
Gotcha sorry I misunderstood. I have heard of people replacing the plugs with zirks and I never understood that. thanks GT
1976 and 1977 Challengers
Many have done it. The issue is the bearings are Babbitt. Once the grease is displaced, it's like it's not there. The bowl does not get warm enough to drop the oil out of the base. A roller element bearing is a different story.
GT
Sent from my SM-G900V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)
-
Thanks helpful as always
1976 and 1977 Challengers
-
Gotcha sorry I misunderstood. I have heard of people replacing the plugs with zirks and I never understood that. thanks GT
1976 and 1977 Challengers
I did that on 2 berk bowls without any issues... If you do plan on it though, get a center tap an mark the outer facing around the inside o-ring. Berks didn't have a seal clip an pressure could slide the inner seal off.
-
Mine has worked just fine for over 40 years with A LOT of use with just gear oil I think I will leave well enough alone lol
1976 and 1977 Challengers
-
Mobil1 synthetic. Great reputation, widely available, and always mentioned in these discussions on jet boat forums.
-
Mobil1 synthetic. Great reputation, widely available, and always mentioned in these discussions on jet boat forums.
Mobil 1 is a brand, not type. Use the lithium or the SHC type.
There are quite a few greases available from Mobil.
Great stuff, we use the Chevron stuff at work, same basic stuff.
GT
Sent from my SM-G900V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)
-
Mobil 1 is a brand, not type. Use the lithium or the SHC type.
There are quite a few greases available from Mobil.
Great stuff, we use the Chevron stuff at work, same basic stuff.
GT
Sent from my SM-G900V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)
And information only, not bagging.....
GT
Sent from my SM-G900V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)