SoCal Jet Boats
Tech Talk => Engine Mechanical / Electrical => Topic started by: 2savage4you on February 18, 2010, 10:21:05 AM
-
Anybody buy any reman engines lately , where is the place to go to get a good rebuild?
I know the chevy crate motor would be my Best bet or rebuild it here in my garage but i kinda want to just do a swap....
i need one with TBI not carbed........................
-
i use these guys alot 2sav! here i took the liberty of looking it for you
http://search1086.used-auto-parts.biz/cgi-bin/search.cgi
-
i use these guys alot 2sav! here i took the liberty of looking it for you
http://search1086.used-auto-parts.biz/cgi-bin/search.cgi
Thanks but cant seem to get in it..
Ive been looking alot myself, not in any hurry but i want to have it lined up when im ready...
-
if i was gonna go that route this is what i would do
https://shop.enginekits.com/osb/itemdetails.cfm?ID=81
the cost of it is 470 if you dont do any upgrades and would be a little more power for that 1500 you got there hell you could have it done in a couple of days easily
-
::) now thats what im talking about... the only thing i would have to do is reprogram the computer and maybe a bigger TB:banghead:
but thanks for the link, im going to go out and yank this bitch out and stroke her ;D
-
My buddy works at Checkers, might be able to get a good deal, I think normally there around 1k for a long block.
I also have some SBC parts I'm kicking around, fresh bored block, one good head.... but if you're interested in possibly building one for cheap give me a call :thumbup:
-
My buddy works at Checkers, might be able to get a good deal, I think normally there around 1k for a long block.
I also have some SBC parts I'm kicking around, fresh bored block, one good head.... but if you're interested in possibly building one for cheap give me a call :thumbup:
yes i am interested in the block, not sure if it is the same as i have now but im seriously thinking of changing this thing over to a nice carb motor and delete all this electronics ;D
just watched another c1500 with a 383 on youtube, did this rolling burnout was just sick :sly:
-
Steve I have to good running SBC's , one is 350 the other is 327 both are 2 bolt mains both both have fuely heads and are turn key complete from pan to intake Buildin a 383 with a new block and heads to replace one as we speak call if your interested Tom
-
Steve I have to good running SBC's , one is 350 the other is 327 both are 2 bolt mains both both have fuely heads and are turn key complete from pan to intake Buildin a 383 with a new block and heads to replace one as we speak call if your interested Tom
That 350 would be great , but no way to get it here :thumbdown:
-
Easy to get to Socal though , just a thought ... Tom
-
I have a late model "Factory Roller 350"
1. Block...1 pc rear main/pass side dip...all machined
2. 5.7 rods
3. heads/with valve job.
4. 3.480 crank/cast.
All apart....Customer ran outa $$....can make you a deal...came outa corvette.
If u r interested pm me.
-
I have a late model "Factory Roller 350"
1. Block...1 pc rear main/pass side dip...all machined
2. 5.7 rods
3. heads/with valve job.
4. 3.480 crank/cast.
All apart....Customer ran outa $$....can make you a deal...came outa corvette.
If u r interested pm me.
pm sent
-
i just went out and did a compression check on my sbc and i think i found why it seems to miss......
#8=145 #7=130
#6=155 #5=120
#4=150 #3=50 :screwy:
#2=165 #1=150
Well just when i thought i was close to being finished with this thing o'well i planned on building a HP motor for it down the road but looks like im doing it sooner than i thought.
gonna pull the V/C's off just out of curiosity and see whats under them ???
-
I have a late model "Factory Roller 350"
1. Block...1 pc rear main/pass side dip...all machined
2. 5.7 rods
3. heads/with valve job.
4. 3.480 crank/cast.
All apart....Customer ran outa $$....can make you a deal...came outa corvette.
If u r interested pm me.
I did send you a pm maybe you didnt get it , but would you want to let those heads go ?
if so pm me a price please..
VORTEC right :sly: