SoCal Jet Boats

Tech Talk => Engine Mechanical / Electrical => Topic started by: AQUAHOLIC on May 06, 2008, 06:20:31 PM

Title: where can i get these fittings
Post by: AQUAHOLIC on May 06, 2008, 06:20:31 PM: i need six of them

(https://www.socaljetboats.com/proxy.php?request=http%3A%2F%2Fi15.photobucket.com%2Falbums%2Fa399%2Fvr4tony%2Finternet005.jpg&hash=b32c08c3b69085e794a976c3f8b7f2678c5f7c9e)
Title: Re: where can i get these fittings
Post by: TJS Nordic on May 06, 2008, 06:48:41 PM: Try McMaster.com
Title: Re: where can i get these fittings
Post by: Luckie Stiff on May 06, 2008, 06:53:26 PM: if those are 3/8" pipe thread X barb, I have 2 or 4 of them in the garage.
Title: Re: where can i get these fittings
Post by: AQUAHOLIC on May 06, 2008, 07:02:12 PM: i think the barb part is 3/8 inch but the threaded part is larger. i will go measure it real quick
Title: Re: where can i get these fittings
Post by: 2savage4you on May 06, 2008, 07:04:22 PM: http://www.cpperformance.com/SearchResult.aspx?CategoryID=330

Specialty fittings

2sav
http://www.cpperformance.com/products/Hose/specialty-fittings.htm
Title: Re: where can i get these fittings
Post by: AQUAHOLIC on May 06, 2008, 07:04:56 PM: ok the threaded part is 1 inch and the barbed part is 5/8 inch.

if anyone has them i have two that will work i was looking to replace all of them with new ones but if i have to use what i can get then so be it.
Title: Re: where can i get these fittings
Post by: AQUAHOLIC on May 06, 2008, 07:10:27 PM: wow i thought you had found them. but i am looking at the site now and i dont see a 1inch npt male to 5/8 slip on hose barb.

or am i just missing it.
Title: Re: where can i get these fittings
Post by: koyota93 on May 06, 2008, 07:31:21 PM: I would call Dave from Sweet Performance. He makes fittings in house. He's in Placentia at the 57 and 91. I think he goes by SuperDave101 on performance boats. I bought some AN fittings from him 2 weeks ago, best prices around and great customer service.
Title: Re: where can i get these fittings
Post by: crewchief22 on May 06, 2008, 07:46:26 PM: If you measured the out side diameter of the threaded part at 1", it will probably be a 1/2" NPT. Pipe is measured inside so the actual size doesn't match listed size.

What I think you are looking for would be 5/8 hose x 1/2 NPT 90 degree.
Title: Re: where can i get these fittings
Post by: AQUAHOLIC on May 06, 2008, 08:59:21 PM: ya i was measuring the outside diameter. i will swing by the shop tomorrow and grab a mic and measure the inside diameter.
Title: Re: where can i get these fittings
Post by: AQUAHOLIC on May 06, 2008, 09:09:10 PM: going by a tape measure the inside diameter is 3/4 by 1/2 i guess i will order some of these and see if they fit.
Title: Re: where can i get these fittings
Post by: crewchief22 on May 07, 2008, 05:44:10 AM: I hope I didn't confuse you, ....the hose barb end is still measured around the out side diameter.
Title: Re: where can i get these fittings
Post by: stc315 on May 07, 2008, 08:07:57 AM: I found some at Lowes in the sprinkler dept. They were with all the brass stuff. They had straights and 90's.
Title: Re: where can i get these fittings
Post by: AQUAHOLIC on May 07, 2008, 10:51:44 AM: good to know they are measured differntly. good thing i have not ordered yet. haha i will check the sprinkler section..

thanks guys
Title: Re: where can i get these fittings
Post by: AQUAHOLIC on May 08, 2008, 10:01:10 PM: ok so if i measure the inside diameter i get 3/4 inch on the NTP side. and it is a 5/8 hose barb. so that i am not mistaken this is the size that i need to order.. correct? i want to make sure cause these things ar 16 bucks a piece and i need 6 of them.. totals around 110 bucks with shipping so i want to make sure they are right.