SoCal Jet Boats
Classifieds => Engines / Engine Parts For Sale => Topic started by: Bunger on October 25, 2015, 06:19:15 PM
-
Considering going the single carb route on my boat and maybe a little shot of nitrous. Everything's in great shape and runs great just looking to go a different route. I'd rather sell it all as a package. Buyer gets whole setup intake to scoop.
Asking 1500$ or partial trade for a victor Jr intake for a 455. Thanks
Sent from my iPhone using SoCal Jet Boats
-
Also does anyone have and experience running a victor on a olds? From what I can tell they work somewhat similar to a tunnel ram? Make most power at high rpm?
Sent from my iPhone using SoCal Jet Boats
-
Also does anyone have and experience running a victor on a olds? From what I can tell they work somewhat similar to a tunnel ram? Make most power at high rpm?
Sent from my iPhone using SoCal Jet Boats
I had one on my built Olds... A little sluggish at low rpm, but really woke up after 2500-2800rpm.
I liked it better than the tunnel ram with dual carbs.
Sent from my iPhone using SoCal Jet Boats
-
Hey Phil, what internally did you have done to that motor.
Sent with my Fingers
-
Hey Phil, what internally did you have done to that motor.
Sent with my Fingers
Better question is what I didn't have done to it... A lot easier to list.
Like I always tell people, it's not what in it that's most important, but the blueprinting of all the parts and massaging the engine together. Any bozo can put any engine together, but it takes finesse/patience and a good set of mics to do it right...
Last I heard, the engine I helped you build over the phone and texts is still running strong 😎
Sent from my iPhone using SoCal Jet Boats
-
Better question is what I didn't have done to it... A lot easier to list.
Like I always tell people, it's not what in it that's most important, but the blueprinting of all the parts and massaging the engine together. Any bozo can put any engine together, but it takes finesse/patience and a good set of mics to do it right...
Last I heard, the engine I helped you build over the phone and texts is still running strong 😎
Sent from my iPhone using SoCal Jet Boats
That's a fact! I still appreciate all of your help on that. I learned more then I imagined I would. Thanks brother
Sent with my Fingers
-
I had one on my built Olds... A little sluggish at low rpm, but really woke up after 2500-2800rpm.
I liked it better than the tunnel ram with dual carbs.
Sent from my iPhone using SoCal Jet Boats
Right on. What carb were you running on yours?
Sent from my iPad using SoCalJetBoats
-
Right on. What carb were you running on yours?
Sent from my iPad using SoCalJetBoats
Holley HP 950cfm
Sent from my iPhone using SoCal Jet Boats
-
Holley HP 950cfm
Sent from my iPhone using SoCal Jet Boats
10/4 spoke with George at clay smith today he recommended the same carb
Sent from my iPad using SoCalJetBoats
-
Who's camshafts are all you olds guys running? I'm building a 10.25 461 with a tunnel ram and 2 660s with some home ported heads I did 15 years ago. I'm thinking about running a solid flat tappet
-
Who's camshafts are all you olds guys running? I'm building a 10.25 461 with a tunnel ram and 2 660s with some home ported heads I did 15 years ago. I'm thinking about running a solid flat tappet
I've got a clay smith cam not exactly sure on the specs the cam card got lost. My olds has all forged internals and 9.5:1 and ported heads and a flat tappet.sounds pretty similar to yours.
Sent from my iPhone using SoCal Jet Boats
-
Bump more pics
Sent from my iPhone using SoCal Jet Boats
-
Bump more pics
Sent from my iPhone using SoCal Jet Boats
How much room do you have between the valve cover and header? I have M/T valve covers but can't use them because of the valve train is way too tall
-
Bump more pics
Sent from my iPhone using SoCal Jet Boats
How much room do you have between the valve cover and header? I have M/T valve covers but can't use them because of the valve train is way too tall
Roughly 2 inches. Plenty of room. May be tighter with the twist headers. I have a stock valve train aside from adjustable push rods.
Sent from my iPhone using SoCal Jet Boats
-
I had one on my built Olds... A little sluggish at low rpm, but really woke up after 2500-2800rpm.
I liked it better than the tunnel ram with dual carbs.
Sent from my iPhone using SoCal Jet Boats
I just came across the mondello air gap manifold. What's your opinion on that compared to the victor
Sent from my iPhone using SoCal Jet Boats
-
I just came across the mondello air gap manifold. What's your opinion on that compared to the victor
Sent from my iPhone using SoCal Jet Boats
The mondello air gap is most likely a procomp copy of the edelbrock 7551.
That's an excellent all around manifold.
Dual plane, and it's pretty tall. Best of both worlds.
I think it will be more efficient on your set up, but you will loose the "cool" factor of your tunnel ram. Btw, your setup looks killer.
But I can assure you, your engine will RUN killer with the airgap.
Either way, I wouldn't buy Chinese procomp stuff.
Sent from my iPhone using SoCal Jet Boats
-
The mondello air gap is most likely a procomp copy of the edelbrock 7551.
That's an excellent all around manifold.
Dual plane, and it's pretty tall. Best of both worlds.
I think it will be more efficient on your set up, but you will loose the "cool" factor of your tunnel ram. Btw, your setup looks killer.
But I can assure you, your engine will RUN killer with the airgap.
Either way, I wouldn't buy Chinese procomp stuff.
Sent from my iPhone using SoCal Jet Boats
The tunnel Rams cool but I'm looking for simplicity. Twice as much shit to worry about. And I'm tired of constantly polishing the damn thing haha. I love the way the victors look with a fiberglass scoop.
Sent from my iPad using SoCalJetBoats
-
Mondello prep'd 468 short block, jm-30 cam,eld heads,Harlan sharp 7002 , rollers,9.8restricted pushrods, comedic MLS headgaskets,eld 28101P intake(I really don't mind polish'n on a cold winters night ,w/a shot of Jack Black LOL),proforma 950 all in pieces for now.....sh-t!
-
Pics.
-
I dig your pressure regulator setup. I might steal that idea. What kinda rpm do u plan to pull
Sent from my iPhone using SoCal Jet Boats
-
Now that's going to be one sexy Olds what valve covers do you plan on running
-
The reg plate and lines from Summit.As a kit kinda thing.Rpm prolly 52/53hundard,not too high,TBD. Valve covers are ebay score,aluminum plate,dimed up nice an polished. I do most of my cruising around the docks checking the chicks out, on the sun pads of daddies 72 foot MYaught houseboats. Or hold up in a cove some place with ZZ Top on the stereo and thank you for your kind words
-
BTW Bunger, that's one kikazz Offy induction u got. I'm luvn' it
-
BTW Bunger, that's one kikazz Offy induction u got. I'm luvn' it
Thanks man. Im thinking I'm actually gunna Keep it now haha.
Sent from my iPhone using SoCal Jet Boats
-
Anyone know of a shop that makes a rail kit for bbo's?
Sent from my iPhone using SoCal Jet Boats
-
Anyone know of a shop that makes a rail kit for bbo's?
Sent from my iPhone using SoCal Jet Boats
http://www.marineindustrieswest.com/GroupCatProducts.cfm?CatId=814,503&group_id=63&page=1&CFID=7042617&CFTOKEN=4507351-28813b3a-eccf-42de-8976-25539de1f1cb (http://www.marineindustrieswest.com/GroupCatProducts.cfm?CatId=814,503&group_id=63&page=1&CFID=7042617&CFTOKEN=4507351-28813b3a-eccf-42de-8976-25539de1f1cb)
Maybe Marine Industries West/Dana Marine/BJ's Marine/ Recycle Performance can help you out.