SoCal Jet Boats

Classifieds => Engines / Engine Parts For Sale => Topic started by: shield3 on February 06, 2017, 07:44:03 AM

Title: Mopar 440 Iso
Post by: shield3 on February 06, 2017, 07:44:03 AM

Taking on a project and currently looking for the bell housing and motor mounts for a 440. If you have it or can point me in the right direction I'll gladly appreciate it. Thanks in advance

Sent from my XT1650 using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)

Title: Re: Mopar 440 Iso
Post by: mash on it on February 06, 2017, 07:53:48 AM

Try Tom @ Jet Boat Performance.

I think a rail kit and plates could easily be made for RB's

I've seen a classified here for bellhousing and headers before, maybe a couple of years ago.

Dan'l

Title: Re: Mopar 440 Iso
Post by: shield3 on February 06, 2017, 08:31:38 AM

OK that sounds great and I think the bell housing is going to be the hardest to find

Sent from my XT1650 using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)

Title: Re: Mopar 440 Iso
Post by: Flusher on February 06, 2017, 12:11:42 PM

I always wanted to do a B/RB/Hemi rail kit.

Attached are the factory blueprints.  Be advised that Figure 3-18 Bellhousing Bolt Pattern is the view facing the transmission input shaft or the rear engine plate from the front (timing cover side) of the block.  Unfortunately this print doesn't have the dimensions for the starter, which will mount directly to the plate.

Using a rail kit would eliminate use of a bellhousing or any type of 3-point mount system.

A simple flywheel cover can be fabricated from the attached prints or a more common flywheel cover from a BBC, such as a Lightening, as is the case with a BBF rail kit.

The front motor plate(s) should be similar to Figure 3-27 and pick up only the water pump mounting locations.  Utilizing the timing cover fasteners would cause fitment issues with the harmonic damper and front main seal, there isn't enough clearance to move the cover 5/16" to 3/8".  Tap the plates directly with 3/8-NPT minimum for water in/out, bottom holes are water in and top are water out.

Good luck,

Joe

Title: Re: Mopar 440 Iso
Post by: shield3 on February 06, 2017, 12:53:45 PM

Sweet thanks alot Joe this has been really helpful

Sent from my XT1650 using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)

Title: Re: Mopar 440 Iso
Post by: crewchief22 on February 07, 2017, 05:22:57 AM

I have a nice set of Edelbrock logs and snails for a 440, If you're interested.

Title: Re: Mopar 440 Iso
Post by: shield3 on February 07, 2017, 03:54:36 PM

Can u send me a picture

Sent from my XT1650 using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)

Title: Re: Mopar 440 Iso
Post by: crewchief22 on February 07, 2017, 06:01:01 PM

Pics


Sent from my iPhone using SoCal Jet Boats

Title: Re: Mopar 440 Iso
Post by: rush1 on February 08, 2017, 06:21:38 AM

Greenwood marine has bell housings

Sent from my SM-G930V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)

Title: Re: Mopar 440 Iso
Post by: rush1 on February 25, 2017, 08:39:20 PM

Quote from: rush1 on February 08, 2017, 06:21:38 AM

Greenwood marine has bell housings

Sent from my SM-G930V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)

I meant to say Glenwood

Quote from: crewchief22 on February 07, 2017, 06:01:01 PM

Pics


Sent from my iPhone using SoCal Jet Boats

Quote from: rush1 on February 08, 2017, 06:21:38 AM

Greenwood marine has bell housings

Sent from my SM-G930V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)

Sent from my SM-G930V using SoCal Jet Boats mobile app (http://r.tapatalk.com/byo?rid=201)