SoCal Jet Boats
Tech Talk => Jet Pumps => Topic started by: flytime on March 09, 2008, 09:03:46 PM
-
Thinking about having my Berk. re powder coated. Does anybody know anyone in Orange County that does this? What I should expect to pay? Advantages/disadvantages. Reason being....my place diverter looks brand new and the rest of the pump does not. Kinda bugs me. :screwy:
Bob
-
Embee Coatings?
-
Just make sure to remind them not to coat inside threads or where your diverter or steering and mating surfaces of the pump. Some places will even put a small round pad where bolts etc. go so it will keep threads clean and so you wont crack and scratch the finish around the bolt hole when you put it back in the boat and torque it down
-
Poder coating is nice but my dad and I have always just painted ours with automotive paint. Looks nice and is not that much to do.
Just my .02 :)
-
Poder coating is nice but my dad and I have always just painted ours with automotive paint. Looks nice and is not that much to do.
Just my .02 :)
I did a good job of primer coating with a lacquer spray can, then got some appliance white, it was the whitest I could find and gave it 2 or 3 coats. Let dry for a couple of days and then hand brushed the Berkeley name back on. The Place Diverter which is powder coated has a different white when put together. When the paint gets bad, I can strip it off and re-do it for about $20.00.
-
you should be looking between 200-300 dependes on how much sand blasting your pump reqiures
-
Check Orange county sandblasting - They are right at the RR tracks in old town orange - on either La Vita or Palmyra just west of glassel.
I know they do anodizing, I think they do p'coating.
-
re powder coating ... we litterally cringe when the subject comes up weve seen every powder coat disaster scenario imaginable : overspray , PC on macined surfaces ,bowl bushing issues and ,even a distorted suction (from heat) Clean, strip, sand , clean again and paint (satin rustoleum) or Kragens engine paint ... just my 02 ....Tom
-
Thank you all for your input. I just want that shiny white look back. IMO if Tom thinks its a bad idea than it probably is. When I get the boat back home in a couple of weeks I will take another look at it. I might just be picky.This may turn out to be an after summer project. I dont want to have problems in the middle of the project and get hosed out of some nice boating weekends.
Bob
-
re powder coating ... we litterally cringe when the subject comes up weve seen every powder coat disaster scenario imaginable : overspray , PC on macined surfaces ,bowl bushing issues and ,even a distorted suction (from heat) Clean, strip, sand , clean again and paint (satin rustoleum) or Kragens engine paint ... just my 02 ....Tom
How long does the rattle can last?
-
How long does the rattle can last?
I guess it all depends on how you care for your pump. I think you can buy epoxy in rattle can and that should hold up better.
-
Routine maint., cleanings, etc.... a year, 2, longer?
-
Routine maint., cleanings, etc.... a year, 2, longer?
OC, Look at it this way. If you get a scratch in the finish, you can smooth it out and hit it with a couple of coats of rattle can epoxy, let dry and you're good to go until the next ding. Powder coating would be more difficult to repair. You might even be able to hit the surface with a 3M Scotch Bright pad and then run a buffer over it and bring back the shine.
-
How long does the rattle can last?
Jeremy it depends on how many building I Tag with it ;D ;D ;D
Just kidding good quality spray paint wont hold up to powder coat ,no question , but I'm just not a fan of the P/Ctng