SoCal Jet Boats
Tech Talk => Outboards => Topic started by: quick olds on March 14, 2015, 03:00:05 AM
-
So i cleaned up the prop on the mini and added a little edge i was just wondering if this helps at all aor did i waste my time its a tohatsu 40. And from what ive read its an 11 pitch stock prop
-
11.6 diameter acording to tohatsu
-
Propellers are all about smooth, not necessarily sharp. The front surfaces of the blade should be as flatty add possible with the imperfect surfaces on the back.
Think of an airplanes wing.
You are probably closer to a 13 pitch if the boat planes well. That should be a through hub exhaust, so if it struggled to get on plane, you can always drill some vent holes to let it "slip" a little on launch of it had problems with the 13. A 13 pitch may also be slightly smaller in diameter. Like a 10.8.
GT
Sent from my SCH-I545 using SoCal Jet Boats mobile app
-
Ok cool it got on plane fine and its thru hub exh ill measure the diameter today to measure diam i believe i should measure the radius to outside edge of fin and x2 to get diam is this correct? Also the prop is stamped with 11 and online for factory props 11p standard equip but i jave no idea what im lookin at.
-
It revved fast though im testing with a tach tomorrow to see what it turns but once on plane the rev to mph difference seemed almost as though it would rev quick and not go much faster. Its a river/ cruiser boat so im not pulling any thing with it like tubes or skiers so im mostly lookin for the most prop itll turn and still get on plane managably.
-
Pic
-
Pic
-
This is what i did got the dings out and basically blended it
-
I talked to the prop shop today. The only thing he has right now is a 50 hp Nissan prop that he said won't work on your shaft. He also ssid that thing should be able to pull a 13 with little drama.
Sent from my SM-G900V using SoCal Jet Boats mobile app
-
Sweet im gonna see what im turning tomorrow any guesses? Im thinkin 6100
-
Ill definitely go thru him when i find everythjng out and am ready for a prop though.
-
6800 at wot i think i need a prop
-
6800 at wot i think i need a prop
Yep, need to drop it down over 1000RPM. My guy was right, it should pull a 13. I will try to whiz by there tomorrow afternoon. He owes me lunch anyway... :thumbup:
GT
-
Awesome ya it jumps outta tho hole hard so it should pull a 13 maybe maybe even 14 fine it dont weigh much also i need a float mine sunk
-
Yep, need to drop it down over 1000RPM. My guy was right, it should pull a 13. I will try to whiz by there tomorrow afternoon. He owes me lunch anyway... :thumbup:
GT
Also any idea of where to get a float for this carb?
-
Yep, need to drop it down over 1000RPM. My guy was right, it should pull a 13. I will try to whiz by there tomorrow afternoon. He owes me lunch anyway... :thumbup:
GT
Also any idea of where to get a float for this carb?
-
Sierra Should make it, otherwise, West Marine used to sell Tohatsu. So maybe them...
GT
-
Sweet thanks man. Are you going to the Bluewater meet?
-
Sweet thanks man. Are you going to the Bluewater meet?
I really want to. My pop is waiting on some finalized paperwork on my grandmothers old house in Big River. If we get it handled before then with plenty of notice, then yes... It is a long drive, so I am not sure if I will be dragging a boat. I really want to get the Mouse powered Southwind down there... Maybe.
GT
-
Well if you make it i owe you a few beers if not we will have to figure out a day and go to the lake or river
-
Well if you make it i owe you a few beers if not we will have to figure out a day and go to the lake or river
Works for me.... I plan on having some fun this summer.. Getting old sucks. :thumbdown:
GT
-
Cool i wanna see the is mouse powered boat too. Im gonna call west marine tomorrow and see if i caan find that float i found one online but they want 22 bucks for it if i have to ill pay it but seems steep for a piece of plastic lol.
-
Going to check tractor supply i searched it on a gut feeling and they have brass univ r sal floats in a different sizes for less thaan the plastic oem
-
So lookin at props i am kinda I nterestedbin this kne let me know what you think http://m.overtons.com/modperl/product/details.cgi?from=grid&i=7008584 its about half ins smaller in n diameter and is 4 inches of pitch bigger ? Taller ? However its worded lol if its true that ill get 200 or so rpm less eper pitch change this should put me at 6k