1
Random Boat Parts For Sale / Re: HUGE parts sale
« on: October 22, 2016, 06:12:49 AM »
Do you still have that water thermostat splitter and the header waterlines?
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Boats For Sale / Re: 78 Nordic tunnel for sale
« on: October 19, 2016, 01:47:19 PM »
Looks like a good boat. I like it
3
The No Wake Zone / Re: I want to see tow riggs
« on: October 07, 2016, 04:37:16 AM »
I've got a 3500 pound class III tow hitch on my beauty.
4
Random Boat Parts For Sale / Re: Low profile intake
« on: September 18, 2016, 06:10:57 AM »
Can you explain or show me a couple pictures of the difference between a low profile intake in a regular intake thank you
5
Jet Pumps / Re: Identify this bowl stuffer Plz. I WTB one thanks
« on: September 12, 2016, 10:16:31 AM »
Good info I will make it I do have access and experience with the machines. Generally do you try to make the labyrinth seal on the lip that is going into the impeller rather than a flat surface bolting onto the bowl? That seems to make the most sense to me
6
Jet Pumps / Re: Identify this bowl stuffer Plz. I WTB one thanks
« on: September 10, 2016, 12:12:31 PM »
Horse power to weight ratio Every ounce matters 😀
If we're just talking tenths of a second with the difference in Stafford plates that's not really what I was looking far so it sounds like a plate might be my Best option. I just liked the way the one I had showed backfilled the impeller so there is less water friction as possible.
How thick of a plate generally do you need. Just asking so I know what kind of piece of flat plate I'm going to be buying for this project to start with
If we're just talking tenths of a second with the difference in Stafford plates that's not really what I was looking far so it sounds like a plate might be my Best option. I just liked the way the one I had showed backfilled the impeller so there is less water friction as possible.
How thick of a plate generally do you need. Just asking so I know what kind of piece of flat plate I'm going to be buying for this project to start with
7
The No Wake Zone / Re: What did you do to your boat today?
« on: September 10, 2016, 12:01:00 PM »
Drained all the water out from the rain we had last night
8
The No Wake Zone / Re: What did you do to your boat today?
« on: September 09, 2016, 02:10:10 PM »
Changed the loader . Will have to tested this weekend
9
Jet Pumps / Re: Identify this bowl stuffer Plz. I WTB one thanks
« on: September 09, 2016, 02:13:48 AM »
Thanks do you know by any chance if there still available like that. I like that it doesn't drill in to you bearing cavity
10
Jet Pumps / Identify this bowl stuffer Plz. I WTB one thanks
« on: September 08, 2016, 10:11:35 PM »
Identify this bowl stuffer Plz. I WTB one thanks any lead would be good
11
Random Boat Parts For Sale / Re: Parts
« on: September 08, 2016, 09:58:29 PM »
Still have the snoot?
12
Engine Mechanical / Electrical / Re: gate vs ball
« on: September 08, 2016, 09:36:01 PM »
This is a topic I know well.
I will make it as simple as possible.
"A brass gate valve is a good choice for throttling fluids. The brass is very resistant to corrosion. The gate valve allows for fine adjustment of flow. less acceptable to vibration. Good choice for throttling fluids.
"A ball valve is not made for throttling fluids. A ball valve is only meant to be in the open or closed position" with only a 90° turn on the handle you could lose flow very quickly due to a bump vibration or someone accidentally just being too close and bumping it but not realizing. Most of all the ball valve is not intended for throttling fluids. Ball valves are intended to be open or closed.
Be sure not to get a regular outside tap valve. Although you may think they look fairly similar they're not similar in design. Under conditions of high flow the rubber gasket could fold over and close off your flow.
I will make it as simple as possible.
"A brass gate valve is a good choice for throttling fluids. The brass is very resistant to corrosion. The gate valve allows for fine adjustment of flow. less acceptable to vibration. Good choice for throttling fluids.
"A ball valve is not made for throttling fluids. A ball valve is only meant to be in the open or closed position" with only a 90° turn on the handle you could lose flow very quickly due to a bump vibration or someone accidentally just being too close and bumping it but not realizing. Most of all the ball valve is not intended for throttling fluids. Ball valves are intended to be open or closed.
Be sure not to get a regular outside tap valve. Although you may think they look fairly similar they're not similar in design. Under conditions of high flow the rubber gasket could fold over and close off your flow.
13
Random Boat Parts For Sale / Re: HUGE parts sale
« on: September 06, 2016, 06:41:02 PM »
How much is added to the driveshaft?
14
Random Boat Parts For Sale / Re: Berkley Suction Housing
« on: September 05, 2016, 07:54:05 AM »
Would you happen to have the hand hole cover with it also the one that's flush on the inside?
15
Random Boat Parts For Sale / Re: Coplete Legend Pump / Dominator Suction Housings, Race Bowl / Berkeley Housing
« on: September 04, 2016, 12:34:19 PM »
What about the nozzle is that for sale? Separately
16
Boats For Sale / Re: 1988 Eliminator Jet Boat
« on: September 01, 2016, 05:15:31 AM »
Was trying to look at your pics but you just can't see them could you try adding them again thanks
Pages: [1]