1
Boat Showcase / Re: Lets See Your Rides
« on: January 03, 2016, 06:58:54 PM »
1979 sleek craft Kauai 👌
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
3
Jet Pumps / Re: Panther Jet Energizer
« on: January 02, 2016, 08:46:34 AM »
So when I had my panther jet drive I seemed always to have water coming in the boat from somewhere and you could never find it when you're idling in the water or sitting in the water but at high-speed the water kicks back in between the rear Transam where the Jet Pump mounts to the back of the boat pull the pump off clean the two surfaces reseal it with marine grade sealant don't be shy on the sealant get enough on there then remount pump onto transom of the boat. I only found it after hanging over the engine compartment and having someone else drive the boat and I could see it being forced back in at a high-speed at low speeds didn't have enough water pressure to push through the ceiling surface
4
Jet Pumps / Re: Panther Jet Energizer
« on: December 30, 2015, 03:40:32 PM »
I have a good idea of where your leak could be if you're interested leave your number and I could give you a few tips to
5
Random Boat Parts For Sale / Re: DART Tunnel ram and carbs
« on: December 30, 2015, 03:36:47 PM »
It's too bad it's not polished
6
Random Boat Parts For Sale / Re: DART Tunnel ram and carbs
« on: December 29, 2015, 09:49:35 PM »
Why do you call it at 10.190" not a 10.200?
Twinturbo
Twinturbo
7
Random Boat Parts For Sale / Re: Stainless Impeller Berkeley
« on: December 29, 2015, 12:37:05 PM »
Sold Payment pending sorry boys
8
Random Boat Parts For Sale / Re: DART Tunnel ram and carbs
« on: December 26, 2015, 10:47:25 AM »
Has it been milled down?
Not 10.200
Not 10.200
9
Random Boat Parts For Sale / Re: Stainless Impeller Berkeley
« on: December 26, 2015, 06:28:17 AM »
I am told it's a "A"
10
Random Boat Parts For Sale / Stainless Impeller Berkeley
« on: December 26, 2015, 06:27:11 AM »
Stainless impeller Berkeley used. Had plans of increasing horsepower but never have as I'm told this impeller I really don't need at all and may slow my boat down being stainless and a taller pitch. I am told this impellers for high horse power boats and my aluminum is fine for my horsepower an application. If anyone is interested I may be looking to trade for other parts or I'm looking to get $550 or trade looking for a tunnel ram dart. Email me with parts you have also looking for a straight snoop with wedges or tunnel Rams cheers Merry Christmas and thank you
12
Gelcoat / Paint / Fireberglass Repair / Re: SST sleek craft
« on: October 31, 2015, 03:04:10 PM »
What are you running for horsepower and torque plus impeller and RPMs. Thanks
13
Gelcoat / Paint / Fireberglass Repair / Re: SST sleek craft
« on: October 31, 2015, 02:53:39 PM »
Do you have a few more pictures your boat looks good. What type of speeds are you hitting? Thanks
14
Gelcoat / Paint / Fireberglass Repair / SST sleek craft
« on: October 29, 2015, 09:17:10 PM »
1980 SST sleek craft.
I have a few questions help
One there is no exposed stringer. if I was to put a rail kit in how what I anchor it to the floor? Stainless studs which have the screw on the bottom and threads on the top?
As it sits now one stud for the three-point mounting system spins in the floor.
Two. everyone seems to be telling me to set the pump back is it worth all that time and work to set it back. I am mechanically inclined just need some tips and our pictures. A phone number of someone who could give me a few good tips?
Three. Last which would be better for my set up/boat a droop snoot which is on it with the place diverter or a straight snoot ? I don't know which application is better for either or snoot.
you thank
Twinturbo
I have a few questions help
One there is no exposed stringer. if I was to put a rail kit in how what I anchor it to the floor? Stainless studs which have the screw on the bottom and threads on the top?
As it sits now one stud for the three-point mounting system spins in the floor.
Two. everyone seems to be telling me to set the pump back is it worth all that time and work to set it back. I am mechanically inclined just need some tips and our pictures. A phone number of someone who could give me a few good tips?
Three. Last which would be better for my set up/boat a droop snoot which is on it with the place diverter or a straight snoot ? I don't know which application is better for either or snoot.
you thank
Twinturbo
15
WTB / Wtb AA stainless impeller. Straight snoot
« on: October 29, 2015, 08:57:31 PM »
Wtb AA stainless impeller. Straight snoot used
Rail kit to plz
Twinturbo
Rail kit to plz
Twinturbo
16
Random Boat Parts For Sale / Re: Bbc motor mount and a pan for sale
« on: October 28, 2015, 04:33:04 AM »
What is the width of the mounting bracket's? Thanks
Sent from my iPhone using SoCal Jet Boats
Sent from my iPhone using SoCal Jet Boats
17
Random Boat Parts For Sale / Re: Bbc motor mount and a pan for sale
« on: October 28, 2015, 04:31:37 AM »
I sent you a PM. Thanks
Sent from my iPhone using SoCal Jet Boats
Sent from my iPhone using SoCal Jet Boats
18
Random Boat Parts For Sale / Re: F/S...Snoot kit
« on: October 28, 2015, 04:27:01 AM »
Sent a PM
Sent from my iPhone using SoCal Jet Boats
Sent from my iPhone using SoCal Jet Boats
19
The No Wake Zone / Re: Hull capabilities
« on: October 25, 2015, 06:22:46 AM »
I'm not familiar with that hall but I know it makes a difference whether it's a quarter string hull or a full stringer hull.
Your boat should be capable of 75 miles an hour quite easily as long as your hall does not have a hook in the bottom best way to check is a long straight edge on the bottom side of the hull. If it's straight there should be no gap anywhere along the straight edge.
Next would be to add Power to the engine and pump mods. Could be as easily as an impeller and tolerances of you to make it more efficient. One thing everyone will say and agree with I'm sure is speed comes with a price 💰💰💰
Twinturbo
Your boat should be capable of 75 miles an hour quite easily as long as your hall does not have a hook in the bottom best way to check is a long straight edge on the bottom side of the hull. If it's straight there should be no gap anywhere along the straight edge.
Next would be to add Power to the engine and pump mods. Could be as easily as an impeller and tolerances of you to make it more efficient. One thing everyone will say and agree with I'm sure is speed comes with a price 💰💰💰
Twinturbo
20
Random Boat Parts For Sale / Re: BBC Merlin Heads
« on: October 23, 2015, 06:35:07 PM »
Are these aluminum heads? And if so what are the specs thank you
Sent from my iPhone using SoCal Jet Boats
Sent from my iPhone using SoCal Jet Boats
21
Engines / Engine Parts For Sale / Re: Brodix bb2 heads
« on: October 23, 2015, 06:17:11 PM »
What are the specs on the head? Could you PM me please thank you
22
Engines / Engine Parts For Sale / Re: Brodix bb2 heads
« on: October 23, 2015, 06:07:47 PM »
What are the specs on the heads?
Pages: [1]