Null

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - renegade

Pages: [1] 2 3 4
1
Engine Mechanical / Electrical / Re: 455 exhaust gaskets
« on: January 20, 2015, 01:19:09 PM »
Never had any luck with the copper gaskets with the the copper RTV. i use the mr gasket white gaskets. remember to tighten them every couple hours. good luck..

2
The No Wake Zone / Re: What did you do to your boat today?
« on: July 02, 2014, 11:12:22 PM »
Quote from: Cliffjumper on July 01, 2014, 06:17:23 AM
Redneck rail kit is done. 25 dollar scrap angle aluminum.  Three sawzall blades  and three tired guys

Sent from my SPH-L720 using SoCal Jet Boats mobile app
Been there done that.

3
Engine Mechanical / Electrical / Re: rebuild time
« on: June 16, 2014, 04:04:30 PM »
theres a short some were.  :o

4
Engine Mechanical / Electrical / Re: rebuild time
« on: June 13, 2014, 10:02:01 PM »
Nice to see back together. ;)

5
Jet Pumps / Re: Berkeley thrust bearing.
« on: May 10, 2014, 08:58:46 PM »
Went to boulder marine off of wells road.  Good peeps fair price.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


6
Jet Pumps / Re: Berkeley thrust bearing.
« on: May 05, 2014, 07:35:49 AM »
Ok we pulled the pump to save some cost. Thanks for the info.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


7
Jet Pumps / Berkeley thrust bearing.
« on: May 03, 2014, 05:39:37 PM »
Who's a good pump guy in the las Vegas area.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


8
Jet Pumps / Re: Berkeley jet pump
« on: May 01, 2014, 04:51:02 AM »
Thank you for the info.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


9
Jet Pumps / Re: Berkeley jet pump
« on: April 30, 2014, 03:59:03 PM »
Its a ja pump.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


10
Jet Pumps / Berkeley jet pump
« on: April 30, 2014, 03:57:12 PM »
What diverter will fit.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


11
Lake Mead / Re: Jet Boat Church @ Mead
« on: April 26, 2014, 12:34:43 PM »
were at on mead callville or the vegas wash?

12
The No Wake Zone / Re: What did you do to your boat today?
« on: March 16, 2014, 12:24:29 PM »
.029 to .032  on impeller shoulder. No same bearing.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


13
The No Wake Zone / Re: What did you do to your boat today?
« on: March 16, 2014, 10:02:25 AM »
Pulled pump apart and shimed impeller to factory specs. Was out ten thousands.

Sent from my SCH-I535 using SoCal Jet Boats mobile app


14
Engine Mechanical / Electrical / Re: 455 Cam
« on: December 20, 2013, 05:13:40 PM »
I would call comp cams and tell them what engine u got and have the power band in at 48 to 5000 rpms. Not 6 to 6500 rpms its a boat not a car. :thumbup:

15
The No Wake Zone / Re: Post up your cool work pics
« on: December 05, 2013, 03:21:43 PM »
Good

Sent from my SCH-I535 using SoCalJetBoats mobile app


16
Engine Mechanical / Electrical / Re: Dual Holley 600cfm jetting
« on: November 19, 2013, 07:47:44 PM »
Sounds like a ignition problem.

17
Engine Mechanical / Electrical / Re: 455 oil pressure question
« on: October 07, 2013, 10:20:12 PM »
 My olds runs 60 psi cruzzing and 40 psi idleing. 10 seasons on motor with high volume mellings oil pump. if your gauges are working write that seems to low of oil press. i would check mains and rod bearing clearence on the bottom of the crank. you asked..........

18
Engine Mechanical / Electrical / Re: Flexplate ringing
« on: September 15, 2013, 02:21:42 PM »
on some cranks you can put the fly wheel on 3 different ways but you want to put it on the it was ballanced at the shop. if it is on wrong it should vibrate the shit out of the boat. check and make sure everything is tight, make sure u-joints arent worn out too,good luck.

19
Engine Mechanical / Electrical / Re: Cleaning oil out of engine compartment
« on: August 11, 2013, 09:52:54 PM »
Simple green and alot of rags!! :beer:

20
Engine Mechanical / Electrical / Re: exhaust logs
« on: August 11, 2013, 09:45:13 PM »
May need to heat them up and a a big ass steel wedge. take your time try not to gull the sufaces. c.p. performance should have all the gaskets.

21
Engine Mechanical / Electrical / Re: 1972 Glastron resurrection - 454 engine oiling issue
« on: August 10, 2013, 10:47:47 PM »
Install a mechanical oil pressure gauge, go from there :screwy:

22
Engine Mechanical / Electrical / Re: Problems starting when warm
« on: July 25, 2013, 12:10:26 PM »
check and clean needle and seat in carb. i would put a fuel regulator and gauge on to. depending on carbs i set the fuel pressure.

23
Engine Mechanical / Electrical / Re: 454 Popping at idle- WITH VIDEO
« on: July 22, 2013, 05:30:07 AM »
Make sure your wires are in the write fireing order. double check!!!! sounds like a ignition problem. ;)

24
Engine Mechanical / Electrical / Re: 454 Popping at idle- WITH VIDEO
« on: July 20, 2013, 12:21:11 PM »
First due a compression test on all cylinders just to make sure engine is mechanicly sound. that will tell you if the valves and rings are in good shape. sounds like ignition problems, have fun.........

25
The No Wake Zone / Re: Fired up!!!!!
« on: July 19, 2013, 12:44:55 PM »
Give it the true test. :thumbup: test it on the water, good luck.

Pages: [1] 2 3 4

Null

SMFPacks CMS 1.0.3 © 2026