26
V-Drives / Center stear T deck???
« on: July 31, 2008, 11:44:57 PM »
Can anybody give me info. about this hull?
#'s FRKKF-----75
18' 3/4 runner bottom
Thanks
#'s FRKKF-----75
18' 3/4 runner bottom
Thanks
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
27
Engines / Engine Parts For Sale / Re: Blown 468, 744HP, FRESH $9,000
« on: July 13, 2008, 07:10:48 AM »
Delayed responce I know. Was working on a deal for a runner bottom to put it in.
31
Jet Pumps / Re: Intake repair suggestions?
« on: July 12, 2008, 09:44:58 AM »
It's a 540, 1071. dynoed 944HP W/51 pulley and 1012 W/56 @ 6700RPM. Ran it for the first time last weekend, runs good! Been working on it for over a year and got lots of good info. here on the site. trying to post build in the galleries but keeps kicking back. Trying to attach a photo to this post and it does the same. Any suggestions? will try again. Will drop in at the AVI bash next weekend.
Thanks
Thanks
32
Jet Pumps / Re: Intake repair suggestions?
« on: July 10, 2008, 08:49:17 PM »
Thanks for the info. I'm gonna just run it for the summer then!
33
Jet Pumps / Re: Intake repair suggestions?
« on: July 09, 2008, 09:54:30 PM »
Yea, I was hoping to weld a peice on to finish the summer, then take it to MPD. Jack did the original work and I need it to load just a little quicker now with the new motor.
34
Jet Pumps / Re: Intake repair suggestions?
« on: July 07, 2008, 08:29:28 PM »
Yea, I did the grinder thing and actually don't notice a difference in perfomance but since I'm runnin a 950 HP deal I want to get all I can out of it.
35
Jet Pumps / Intake repair suggestions?
« on: July 07, 2008, 01:09:16 PM »
Any local shops fix these? Havasu? How do these fins effect the pump function?
Thanks!
Thanks!
36
Engine Mechanical / Electrical / Re: Crankcase ventilation through headers.
« on: June 13, 2008, 11:38:15 PM »
Hi-tech performance will make anything you want. check out their web site, nice stuff!
37
Engine Mechanical / Electrical / Re: Crankcase ventilation through headers.
« on: June 07, 2008, 07:06:36 PM »
hi-techperformance.com
I sent them an e-mail, will post the response.
I sent them an e-mail, will post the response.
38
Engine Mechanical / Electrical / Re: Crankcase ventilation through headers.
« on: June 07, 2008, 06:37:45 PM »
Does anybody know this shop?
39
Engine Mechanical / Electrical / Re: Crankcase ventilation through headers.
« on: June 03, 2008, 09:59:28 PM »
Thanks for the interest, I have read that PCV valves from a Volvo were used but can't find info. on those either. What about a compression fitting to pipe thread as an adapter?
40
Engine Mechanical / Electrical / Crankcase ventilation through headers.
« on: June 02, 2008, 04:48:47 PM »
I have found kits but none of the valves have have threaded ends on the hose side, anyone know who sells them?
Thanks
Thanks
41
Engines / Engine Parts For Sale / Blown 468, 744HP, FRESH $9,000
« on: May 27, 2008, 11:57:48 PM »
Dyno runs only. e-mail me for build and dyno sheets. The best of internal parts. Professional built, finished in April of this year. You can't build one for this price. rvrlam@citlink.net
42
Engine Mechanical / Electrical / Re: Duel electric fuel pump plumbing.
« on: May 21, 2008, 08:40:39 PM »
Thanks for the input, I will check the pick up sizes.
43
Engine Mechanical / Electrical / Duel electric fuel pump plumbing.
« on: May 20, 2008, 08:17:48 PM »
I am running two 140 mallory electric pumps, can I run the #6 lines from the pumps into a #6 x #10 "T" to the regulator then carbs?
I am trying to supply greater volume as well as having a fuel supply in the event a pump fails.
It was running out of each pump to their own regulators, then out of one of the regulators into a secondary "out" port of the second regulator. Tanks did not empty equally.
Thanks
I am trying to supply greater volume as well as having a fuel supply in the event a pump fails.
It was running out of each pump to their own regulators, then out of one of the regulators into a secondary "out" port of the second regulator. Tanks did not empty equally.
Thanks
44
Engines / Engine Parts For Sale / Re: Blown 468 $7000
« on: April 12, 2008, 04:50:52 PM »
The motor is done, It made 744 HP @ 7000 RPM. 649 LBS torque @ 4600 RPM. Running 16% OD.
If you take out 5% you could run on pump gas.
rvrlam@citlink.net
If you take out 5% you could run on pump gas.
rvrlam@citlink.net
45
Jet Pumps / Re: Power takeoff adaptor, adaptor?
« on: April 01, 2008, 09:53:06 PM »
Glenwoon marine
check out their website
check out their website
46
Miscellaneous / Spam / Re: CraigsList Spam
« on: March 24, 2008, 10:34:31 PM »
This is great!
Hope you make this a permanent topic. I shop the list a few times a week.
Hope you make this a permanent topic. I shop the list a few times a week.
47
Engines / Engine Parts For Sale / Re: Blown 468 $7000
« on: March 22, 2008, 08:36:26 AM »
HP should be in the mid 700's Includes headers and carb linkage. 4 extra pullys and 2 belts, Aluminum pully and belt cover.
rvrlam@citlink.net
rvrlam@citlink.net
48
Engines / Engine Parts For Sale / Blown 468 $7000
« on: March 18, 2008, 10:01:25 PM »
Mark IV block, Merlin heads, Hank's steel crank, Manley H-beam rods, Roller, 671, Mallory. Dooley pan for jet
In the shop now being freshend up, will have a dyno sheet when done in the first of April. Keeping carbs for new motor.
In the shop now being freshend up, will have a dyno sheet when done in the first of April. Keeping carbs for new motor.
49
Engines / Engine Parts For Sale / Re: 2 Holley 750's for a tunnel Ram or Supercharger.
« on: February 24, 2008, 06:29:40 AM »
If you can say that they are good and ready to run I will give $300.00
50
Engine Mechanical / Electrical / Re: Who does ceramic coating of headers ?
« on: February 17, 2008, 06:37:52 PM »
Thanks, Beer Jet sent a link with zoomies.