576
WTB / 4 degree wedge
« on: December 04, 2011, 12:14:38 PM »
looking for a 4 degree wedge for a Berkely JB jet
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
577
The No Wake Zone / Re: Thinking of trading my quad
« on: December 04, 2011, 08:42:03 AM »
dont know what your quad is worth but looks like the boat might be a good deal check for the usual rot and maybe try to run the motor
578
The No Wake Zone / Re: IM GOING TO BE A DAD!!!
« on: November 30, 2011, 12:18:14 AM »
awesome new congrats to you both
579
Jet Pumps / Re: berk rebuild/refresh
« on: November 23, 2011, 08:30:10 PM »
you still have to tighten up the new one
580
The No Wake Zone / Re: New SCJB Store NOW LIVE!
« on: November 23, 2011, 08:25:34 PM »
dont know if mine came away till end of the month
581
The No Wake Zone / Re: Happiness is a clean shop
« on: November 20, 2011, 10:30:23 PM »
looks good Josh almost makes me want to clean up my shop 
582
Jet Pumps / Re: berk rebuild/refresh
« on: November 18, 2011, 03:52:05 PM »
just took mine off 2 weeks ago . I had to use my cutting torch and a lot of heat then an 1 13/16ths wrench with a 4 foot baar to get it off then a 3 jaw puller for the impeller. Harbour frieght should be cheap for the wrench good luck and no worries with heat
583
The No Wake Zone / Re: Re: Shirts: Buy 4, get 1 Free
« on: November 15, 2011, 09:25:02 AM »I just looked into it and it looks like they offer a 3xl/4xl product now, I just need to add it into the store with the artwork n stuff. I'll get that set up here soon
Also, they offer American Apparel shirts as well. If anyone is interested, I can set those up - but of course they are a bit more.
Thanks Brad
Sent from my SGH-T959P using Tapatalk
584
The No Wake Zone / Re: Proud of my son (Cow Elk hunt)
« on: November 14, 2011, 01:16:36 PM »
all the time but just the leg bones and we feed them raw
585
Jet Pumps / Re: Jb bowl removal
« on: November 10, 2011, 03:13:24 PM »Mike the box is on its way. The .
586
Jet Pumps / Re: Jb bowl removal
« on: November 09, 2011, 07:34:57 PM »
after heating for at least 20 minutes the nut finally came off then the impeller came off with just a slight pull now ups to Rivertard tomorrow
now ups to Rivertard tomorrow587
Engine Mechanical / Electrical / Re: new scoop
« on: November 09, 2011, 07:31:42 PM »
alumium and for sure on pics. Had it at $50.00 for almost a week the some guy bid 65 then never bid again
588
Engine Mechanical / Electrical / new scoop
« on: November 09, 2011, 03:57:44 PM »
my latest aquisition got it on Ebay for $66.00 
589
Jet Pumps / Re: Jb bowl removal
« on: November 09, 2011, 03:17:12 PM »
thanks probably not a bad idea
590
Project Boats For Sale / Re: Sanger Hydro/jet with an orig. Gale Banks BBF
« on: November 09, 2011, 09:26:38 AM »
i think that it has major structural problems like a rotton transom the cracks in the bow and the way it looks buckled in some of the pics. I think it needs way more than his artist friend to be safe, I would run like hell in the opposite direction but thats just me I could be wrong
591
Jet Pumps / Re: Jb bowl removal
« on: November 08, 2011, 10:28:19 PM »
now with my fancy pulling fixture bowl removal will always be a snap 
havnt tried heating the nut but that will come shortly. sounds like the impellor will be a real bugger from what ive seen so far not sure how you attach a puller to it 
havnt tried heating the nut but that will come shortly. sounds like the impellor will be a real bugger from what ive seen so far not sure how you attach a puller to it
592
Jet Pumps / Re: Jb bowl removal
« on: November 07, 2011, 10:22:59 PM »gord how come you didnt just pull the pump out?
its super easy, and the transom adapter is easy to get off too!
may make you job much easier!
its not been a hard job and I didnt want to chance hurting the paint
593
The No Wake Zone / Re: Proud of my son (Cow Elk hunt)
« on: November 07, 2011, 01:22:43 PM »
awesome job I know just how you feel
594
Jet Pumps / Re: Jb bowl removal
« on: November 06, 2011, 10:51:07 PM »
so the nut really seems to be on there. we tried a wrench with a 5 foot piece of pipe no go. so i am going to make up a deep 1 7/8 inch socket and use an impact wrench. is it right hand thread?
is the impellor keyed on the shaft or how do I get it off dont see where I could attach a puller thanks guys also tell me anything else to watch out for,change or replace while its apart. the shaft has some scoring where the seal rides dont know if thats critical.i guess I could weld it up and machine it back down if needed.is the impellar nut 1 13/16 or 1 7/8 I just watched a youtube video that says 1 13/16 but mine measures a little over that.
is the impellor keyed on the shaft or how do I get it off dont see where I could attach a puller thanks guys also tell me anything else to watch out for,change or replace while its apart. the shaft has some scoring where the seal rides dont know if thats critical.i guess I could weld it up and machine it back down if needed.is the impellar nut 1 13/16 or 1 7/8 I just watched a youtube video that says 1 13/16 but mine measures a little over that.
595
Jet Pumps / Re: Jb bowl removal
« on: November 06, 2011, 10:44:28 PM »Can we borrow the tractor too?
Ray
you pay the freight its yours I can spare that one I have others
596
Jet Pumps / Re: Jb bowl removal
« on: November 06, 2011, 04:49:44 PM »
we machined up a shaft 1inch and 3 eighths 12 threads per inch. then welded a pulling ring on the end . please no comment on the farmer weld . then we hooked a chain block to it put tension on it and tapped the sides with a mallett.the bowl came right out. now I have to make up a real deep 1 and 7 eighths socket to get the nut off the shaft.If anyone wants to borrow the puller let me know
597
Boats For Sale / Re: Craigslist & ebay boats
« on: November 06, 2011, 11:33:46 AM »598
Gelcoat / Paint / Fireberglass Repair / Re: NEED PAINT!!!
« on: November 05, 2011, 08:22:24 AM »
welcome we like pics and we have a old saying cheap aint good and goood aint cheap
599
Miscellaneous / Spam / Re: FS: Doberman Pinscher Puppies
« on: November 02, 2011, 10:27:40 PM »
nice pups Josh
600
Jet Pumps / Re: Jb bowl removal
« on: October 26, 2011, 07:07:18 PM »
turns out the hole is 1.25 inch fine thread. when I get home from hunting next week we will machine up a short threaded shaft and lightly pull on it while hitting the bowl with a mallet. will take pics