801
Engines / Engine Parts For Sale / Re: BBC top mount starter
« on: April 14, 2009, 01:32:28 PM »
Looks like everybody has a chevy starter for sale 
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
802
The No Wake Zone / Re: newbie to these forums
« on: April 14, 2009, 12:35:51 PM »
Fresh meat 
I mean welcome
I mean welcome
803
Boat Showcase / Re: Eliminator
« on: April 14, 2009, 12:32:21 PM »Bring it down to Parker this weekend and my cheap ass will by you a drink.
Mark, where's your cooler?
Would love to , but im still working 7 days
And getting seriously burned the F- out...........
804
Engines / Engine Parts For Sale / Re: BBC top mount starter
« on: April 14, 2009, 12:21:03 PM »
No worries , i usually jack my own thread
805
Engines / Engine Parts For Sale / Re: BBC top mount starter
« on: April 14, 2009, 12:12:31 PM »
OK now that we have scared everybody away from buying a top mount.
Make offer
Make offer
806
Random Boat Parts For Sale / Re: Bimini top
« on: April 14, 2009, 12:10:39 PM »
This needs to go, make offer
807
Boat Showcase / Re: Eliminator
« on: April 14, 2009, 11:37:21 AM »When you're running with him you need to think about that, because if you beat up on him too bad, you might end up working on the Eliminator even more (to make it faster).
Your right , good thinking
Congrats steve, I know its not "Yours" but either way you got a boat on the water!
Thanks bro,
Talk about a stress reliever
Mine will be done in a matter of days..
Put it this way , i could run it today
808
Audio / Re: Woofers for sale if anyone is interested!!
« on: April 14, 2009, 11:27:42 AM »
Man that is tempting 
I need those in the back of my Yota
I need those in the back of my Yota
809
Boat Showcase / Re: Caribbean
« on: April 13, 2009, 07:34:16 PM »
mine has annular boosters
811
Boat Showcase / Re: Caribbean
« on: April 13, 2009, 07:18:58 PM »Steve do you still need a carb? I got a new 850 Marine no air horn, its the one on my boat less than four hours on it.
Ive got a 850 Annular carb im gonna run
812
Boat Showcase / Re: Caribbean
« on: April 13, 2009, 07:00:48 PM »Very nice Steve, you rigged the boat clean.
Thanks, i just hope she runs as good as she looks.
813
Boat Showcase / Re: Eliminator
« on: April 13, 2009, 06:58:18 PM »that was pop in laws, i thot it was his too for a sec. But hey, he 'bout built that one too
Was a pain in the
But well worth it when he dropped the hammer down and his face just lit up Too bad he wont be able to keep up with me
814
Engines / Engine Parts For Sale / Re: BBC top mount starter
« on: April 13, 2009, 06:32:35 PM »Hrm.. I've got that same starter for my BBF.. And it'll catch and grab once or twice, then spin.. Are you having the same issue? It had a bottom mount starter on it before as well.
Yes , if it had a bottom mount... Do yourself a favor and go back to it.
815
Boat Showcase / Re: Eliminator
« on: April 13, 2009, 06:05:00 PM »Way to go Steve!!!!! Shoulda hollered I'da come down. We were shacking down Brads cruiser on mead. Nice day....naked boobies at Sandy
Boobies......Nice
816
Boat Showcase / Re: Caribbean
« on: April 13, 2009, 06:01:25 PM »
Today turned out to be a very eventful day... Got the Eliminator running great and got my package today.
My new bolt on breathers and v/c gaskets installed.
My header control valve.
Tomorrow i change the filter and add oil. Install the new (Oh shit bar for the G/F )
got the entire boat wired but nothing works after the slave solenoid. I jumped it and worked fine so i think i need a new solenoid
Todays monday and im on schedule
My new bolt on breathers and v/c gaskets installed.
My header control valve.
Tomorrow i change the filter and add oil. Install the new (Oh shit bar for the G/F )
got the entire boat wired but nothing works after the slave solenoid. I jumped it and worked fine so i think i need a new solenoid
Todays monday and im on schedule
817
Boat Showcase / Re: Eliminator
« on: April 13, 2009, 05:51:55 PM »
here are some pics from todays shake down.
The river.
Then went to the lake.......
Launch ramp was busier than shiat
She's a runner now she needs to get a detail cause she looks like shit
The river.
Then went to the lake.......
Launch ramp was busier than shiat
She's a runner
now she needs to get a detail cause she looks like shit
818
Boat Showcase / Re: Eliminator
« on: April 13, 2009, 12:57:17 PM »Ok got the Eliminator wet today , but not without some issues.
#1. Lots o water coming out the weep holes at idle (installed a new ball /spring prior )
#2. it takes a while to get the water to come out the dump unless you rev it to 2K then its fine for awhile and then stops
#3.so far no oil in water.
This has a pressure reliefe valve so i open the gate valve full , and i get the rpm's up to see if its working or not and its just a drizzle. i think it starts to dump at 25 psi which i thought was a little high? Or maybe i am
Boat ran strong , really responsive and smooth.. Just need to get the plumbing issues worked out...
Any idea's
Well i was right about it being the "T: valve but wrong about the top........... This is gonna leave a mark
Spring was installed upside down
As soon as i looked i saw the ball stuffed into the spring and knew what i did wrong..
On a good note, took her to the river for a water test .... And she's looking good
Soooooooo.............. Off to the lake for a shake down
Man the water was nice.....
819
Engine Mechanical / Electrical / Re: Oil pan clearance
« on: April 12, 2009, 06:39:20 PM »
thats one thing i never checked when i put the new oil pump/pick up and pan on.... Is clearance
820
Engine Mechanical / Electrical / Re: Header water injection
« on: April 12, 2009, 05:57:02 PM »Easy there Stevie,
Sorry about that Osbo68
I am also dealing with a plumbing issue and talking about yours just got me mad about mine
"Junk" was a bad choice of words on my part
Thanks Jeff
821
Engine Mechanical / Electrical / Re: Bassett injection lines
« on: April 12, 2009, 05:01:16 PM »Those can be tiged. That is an easy fix.
T.J.
Im sure it is for a experienced welder, but im in bullhead and the welder here are scary
Atleast the one ive ran into
822
Engine Mechanical / Electrical / Re: Header water injection
« on: April 12, 2009, 04:49:21 PM »
get the manual and a new T valve cause what you have now is JUNK!!!
823
Gelcoat / Paint / Fireberglass Repair / Re: How to deal with cracking glass on boat floor?
« on: April 12, 2009, 04:47:39 PM »
Your looking at ALOTof work
824
Engine Mechanical / Electrical / Re: Bassett injection lines
« on: April 12, 2009, 04:43:59 PM »maybe some jb weld?
Funny that was the first thing i thought of when i found it
825
Engine Mechanical / Electrical / Re: Bassett injection lines
« on: April 12, 2009, 04:42:06 PM »Steve, if'n it were me I would silver solder those badboys, that is a tiny hole and could be soldered and would last longer than me...
GT
dayum Glenn, i never thought about that....Thanks
Ok problem is fixed ( will be soon
)