801
Engine Mechanical / Electrical / Re: Nicson scoop - Forward or backwards?
« on: June 23, 2013, 04:57:29 PM »
It's a matter of sound, when its forward all you'll hear is it sucking air and its loud. Spin it around and she's quiet.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
802
Gelcoat / Paint / Fireberglass Repair / Re: Help
« on: June 23, 2013, 03:47:52 PM »
If your looking for a solid project I have a full stringer boat with tanks and a berk intake still In it on a single axle I'm letting go for cheap
803
Gelcoat / Paint / Fireberglass Repair / Re: Help
« on: June 23, 2013, 09:47:49 AM »
I'm pretty sure that thing is isn't set up for a je
804
Jet Pumps / Re: Where To Get Jet Boat Parts?
« on: June 23, 2013, 08:14:14 AM »
I found inland boat center in Perris off 4th street is the closest place. Just picked up 2 cables this week, they don't carry much specific for jets but they have everything else. Place is huge.
806
Projects / Re: 71 kona project
« on: June 22, 2013, 04:30:26 PM »
Got to the lake about 2, dropped it in the water get to the no wake marker and no steering. Rack snapped. Pulled the boat out hauled ass home, swapped in my spare cable and rack in 45 mins and now gettin lunch and back to the lake.
I love boats.........not so much right now
I love boats.........not so much right now
807
Random Boat Parts For Sale / Re: Does anyone have a pair of these ?
« on: June 22, 2013, 12:44:38 AM »
They came off my tandem axle the Kona is sitting on
808
Random Boat Parts For Sale / Re: Some stuff for sale
« on: June 22, 2013, 12:36:37 AM »
14's with a ford/Chevy universal lug
809
Random Boat Parts For Sale / Re: Does anyone have a pair of these ?
« on: June 22, 2013, 12:25:45 AM »
14' universal Chevy/ford
810
Engine Mechanical / Electrical / Re: Temp gauge
« on: June 22, 2013, 12:17:45 AM »
Jeez ray I was pointing to it the whole time, I think you need glasses man.
And thanks pat but I ended up picking one up for a 70 chevelle that is 40 degrees off, so 180 on the gauge is really 140 but it should hold me over till I sell off some crap I have laying around to buy a new set of gauges.
Ps. Here's the pic that didn't post earlier
And thanks pat but I ended up picking one up for a 70 chevelle that is 40 degrees off, so 180 on the gauge is really 140 but it should hold me over till I sell off some crap I have laying around to buy a new set of gauges.
Ps. Here's the pic that didn't post earlier
811
Engine Mechanical / Electrical / Re: Temp gauge
« on: June 21, 2013, 09:36:18 PM »
It goes right there and that's one for a 1980 460
812
Engine Mechanical / Electrical / Temp gauge
« on: June 21, 2013, 09:06:03 PM »
So I'm pretty sure my temp sending unit took a dump. Where would I be able to find this little bastard
813
Engine Mechanical / Electrical / Re: Carb gurus
« on: June 21, 2013, 10:59:02 AM »It's the gasket between the carb main body and the plate under the main body u have a hole where the power valve plate goes its blocked by the gasket pm me your number and ill show u which hole it is also what kind of fuel pump u running.
I didn't change that gasket though, and I'm running your standard napa mechanical pump
814
Projects / Re: New Guy, Took in a '72 Omega as payment for a side job....
« on: June 21, 2013, 07:53:10 AM »
They seem to be pretty decent hulls. Few guys on the site have em
815
Engine Mechanical / Electrical / Re: Carb gurus
« on: June 21, 2013, 06:11:38 AM »What kind of carb is it?
Holley 750 dp
id start with seeing if the float was full of fuel. not enough to make it sink , but enough to keep the needle from seating!
Checked that and its fine
Float is stuck. Tap bowl with a sledge hammer. Or a small mallet. Lol
Wasn't sticking
816
Engine Mechanical / Electrical / Carb gurus
« on: June 20, 2013, 09:05:15 PM »
So funny story. I tear down my carb, soak it for a day then clean out every little nook and cranny with carb cleaner and an air compressor. I adjusted everything on the bench and Put said carb back together using a rebuilt kit I purchased from J&M speed out here in riverside this morning and now no matter what I do I have a water fountain out of the secondary overflow. Pulled the needle and seat out found nothing inside causing a bad seal. Used a small screw driver to make sure my float was well...floating and then cleaned out the needle and seat with some air and carb cleaner and reassembled. Still have a fountain. So what am I missing guys?
817
Random Boat Parts For Sale / Re: Some stuff for sale
« on: June 19, 2013, 02:24:52 PM »
Bump
Still have the pan, valve covers, Bimini, drive line/pto, Bassett T and rims
Still have the pan, valve covers, Bimini, drive line/pto, Bassett T and rims
818
Projects / Re: 71 kona project
« on: June 18, 2013, 07:10:35 PM »
Found out why I wasn't getting fuel to the secondaries
819
Engine Mechanical / Electrical / Re: Game: What Broke?
« on: June 18, 2013, 03:16:56 PM »....the oldest joke of all time at the worst time possible. dont be a jackass.
Gotta have a sense of man, that pans still sitting in my garage if ya need it
820
Engine Mechanical / Electrical / Re: Game: What Broke?
« on: June 18, 2013, 02:21:01 PM »
There's your problem, your oil pump and distributor are on the wrong side of the block
821
The No Wake Zone / Re: At the Lake
« on: June 18, 2013, 09:03:57 AM »
A diverter can be the best thing for someone being towed but at the same time it could be there worst enemy. Last time I was towing my brother around he was lipping off because i wasnt going fast enough, a quick up and down on the diverter changed his attitude
822
Random Boat Parts For Sale / Re: Some stuff for sale
« on: June 17, 2013, 06:39:55 PM »
Bassett T 60 bucks
824
Random Boat Parts For Sale / Re: Some stuff for sale
« on: June 17, 2013, 06:35:00 PM »
Bbf pto and berk drive line 120
825
Boat Racing / Re: Crazy Eights @ 2013 Idaho Regatta
« on: June 17, 2013, 03:13:49 PM »
What happened