1
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 10, 2016, 08:24:01 PM »
It's a JB split bowl
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 10, 2016, 07:43:18 PM »
Holy Hammered stuff Batman.
It's surely not helping things.
I assume you pulled the nut?
Get the impeller off and check the port in the suction housing and wear ring clearance.
You need a wear ring, impeller, bearing, seals and packing minimum.
GT
Will I be able to reuse the bowl
3
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 10, 2016, 07:41:50 PM »
Holy Hammered stuff Batman.
It's surely not helping things.
I assume you pulled the nut?
Get the impeller off and check the port in the suction housing and wear ring clearance.
You need a wear ring, impeller, bearing, seals and packing minimum.
GT
I was afraid of that
4
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 10, 2016, 07:31:49 PM »
Could this bowl and impeller be causing my issues
5
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 07, 2016, 02:30:06 PM »
You can see both tabs sticking out front of heads
6
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 07, 2016, 09:09:56 AM »ok. Is it possible that your gate valve by the pump is not opening all the way? Have you looked at that tee for the motor to see if it is an open tee. I am only asking because you said the last motor did the same thing. Especially if you reused the same components over on this motor. That would lead me to believe that one of the components is faulty. What motor are you running?
I did check the gate valve and the tee is open everything originally came out of a ranger jet with a Panther and worked great so transferred all lines as is into the Rogers hull with the Berkeley, motor is a 460
7
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 07, 2016, 08:09:38 AM »In the picture that shows a yellow handled valve and a tee. Is that the tee to the headers or the inlet plates on the motor?
That goes to the headers
8
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 07, 2016, 04:44:14 AM »Just to be sure, when it's running, was there water coming out of the dump line and headers? What was the stream like out of the dump line?
Did the stream change when you opened the dump valve?
Are these the same water lines and fittings you had on your old motor?
I ran water straight thru motor and it seems everything flows fine
9
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 07:00:19 PM »
Here are pics 1st one is inlet 2nd is the plates from t 3rd is housing 4th in back is the truck from inlet to plate front is the headers and 5th is the outlet
10
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 06:55:44 PM »Pics???
[/quote
Little hard for pics my lines run under the motor
11
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 06:46:36 PM »
It's not I thought it was it actually says Panther on it
12
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 06:45:29 PM »
It's actually just a hollow tee that goes to motor water plate
13
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 06:37:19 PM »
It has a 1/2 pipe that comes off the jet to a valve then 5/8 hose to the basset t then that goes up to the plate and then I have 2 lines that comes off thermostat housing both 5/8 one line has a valve for the headers and the other goes to the valve out the back of the boat
14
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 06:20:26 PM »
No a 12jb
15
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 06:19:35 PM »
Berk jg
16
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 05:53:39 PM »
Ok I will try that I had a another motor in the boat and exact same thing was happening to it I was thinking maybe the impeller could be bad maybe
17
Engine Mechanical / Electrical / Re: Overheating issues
« on: July 06, 2016, 05:20:06 PM »
Motor has only been in the boat for a season with very little run time and I have a valve that comes to control how fast the water exits the motor
18
Engine Mechanical / Electrical / Overheating issues
« on: July 06, 2016, 02:57:14 PM »
Boat runs great at any rpm upto 4 grand but once I start hammering on it past that the temp jumps way up gets super hot, inlet valve is all the way open and the outlet is about half I have slowed and opened and doesn't change the problem any advise would be appreciated
19
Events / Re: 2016 SCJB Season Kick Off @ Bluewater, Parker, AZ April 8th-10th
« on: April 11, 2016, 06:17:05 PM »Though I did drive all the way from Houston, my daughter lives in Chandler. It was on my Bucket List to attend one of your events. You all ROCK!!!! Thanks to all the friendly folks I met during the event. Looking forward to the next one in Laughlin in May. You didn't miss anything on Sunday. It was cool, mostly cloudy and windy.
It was good to meet you as well tex
20
Random Boat Parts For Sale / Re: 460 ford logs and snails
« on: February 09, 2016, 06:39:22 PM »
These still available
21
Engines / Engine Parts For Sale / Re: BBF exhaust logs
« on: February 07, 2016, 08:03:29 PM »
We will take them
22
Engines / Engine Parts For Sale / Re: BBF exhaust logs
« on: February 07, 2016, 07:54:15 PM »
Can I get your number
23
Engines / Engine Parts For Sale / Re: BBF exhaust logs
« on: February 07, 2016, 01:44:23 PM »
Where you located
24
Random Boat Parts For Sale / Re: Sand spikes
« on: February 05, 2016, 05:36:59 AM »Looking at making a few more ... any interest?
I'll take one if you get some made up
25
Random Boat Parts For Sale / Re: Lots of jet boat parts for sale!
« on: January 31, 2016, 05:17:26 PM »