1
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Engine Mechanical / Electrical / Re: best bbf stroke length?
« on: October 09, 2010, 12:57:30 PM »
Shitcan the nitrous and the heads, and buy a set of aluminum heads.
Save the money from porting and the nitrous, and have a better all around engine longterm
Save the money from porting and the nitrous, and have a better all around engine longterm
3
Engine Mechanical / Electrical / Re: best bbf stroke length?
« on: October 09, 2010, 11:43:35 AM »
I've had several BBf stroker motors.
The 4.3stk/6.800 rod technically is a great setup. Had this setup also.
The difference in strength between the 4.3&4.5" stroke is nill.
The last engine I built was an all aluminum 604cid. I ran the crap out of that engine in a sand car. 4.500 stk x 4.625 bore w/6.800 rod, 930hp.
Honestly even a cast crank would be fine. But for a few hundred dollars more, why not get the forged crank.
I am currently just starting a new BBF build. Boss hemi heads, 4.5"stroke w/6.800 rods.
I thought about doing the 4.3 stroke, but only for a millisecond.
-Gordon
The 4.3stk/6.800 rod technically is a great setup. Had this setup also.
The difference in strength between the 4.3&4.5" stroke is nill.
The last engine I built was an all aluminum 604cid. I ran the crap out of that engine in a sand car. 4.500 stk x 4.625 bore w/6.800 rod, 930hp.
Honestly even a cast crank would be fine. But for a few hundred dollars more, why not get the forged crank.
I am currently just starting a new BBF build. Boss hemi heads, 4.5"stroke w/6.800 rods.
I thought about doing the 4.3 stroke, but only for a millisecond.
-Gordon
4
Engines / Engine Parts For Sale / Re: WTB Boss 429/460 parts, Boss 9 heads, mounts ect, ect, for Jet boat
« on: October 05, 2010, 04:41:56 PM »
Yes I read your ad. The boss 429 heads are different. Nice manifold you are selling.
5
Engines / Engine Parts For Sale / WTB Boss 429/460 parts, Boss 9 heads, mounts ect, ect, for Jet boat
« on: October 03, 2010, 09:37:55 PM »
I'm looking for:
Boss 9 heads
Boss 429 headers Twistie or straight
Boss 429 blower manifold
Blower idler bracket
Crank hub (1 PC)
drive shaft
motor mounts (Rail)
10 qt oil pan
Will sell or trade the following:
I have complete Kenne Bell Shelby GT500 Twin Screw super Charger kit $4900.00
9" rear axle assembly with 35 spline internals and ARB air locker $2350.00
Kook custom headers ( coated) $850.00
Boss 9 heads
Boss 429 headers Twistie or straight
Boss 429 blower manifold
Blower idler bracket
Crank hub (1 PC)
drive shaft
motor mounts (Rail)
10 qt oil pan
Will sell or trade the following:
I have complete Kenne Bell Shelby GT500 Twin Screw super Charger kit $4900.00
9" rear axle assembly with 35 spline internals and ARB air locker $2350.00
Kook custom headers ( coated) $850.00
6
Hulls / Re: Silhouette boats tunnel open bow jet
« on: September 30, 2010, 09:59:26 AM »
Yah, the guy that owns it told me it needs a big motor; it's a dog with 450hp--40mph uhg
PM'd you ph #,
PM'd you ph #,
7
Hulls / Re: Silhouette boats tunnel open bow jet
« on: September 30, 2010, 09:56:46 AM »
What motor do you have...call me as I'm looking for a big engine now.
8
Hulls / Re: Silhouette boats tunnel open bow jet
« on: September 29, 2010, 09:22:17 PM »
Yes, the one on craigs list.
9
Hulls / Silhouette boats tunnel open bow jet
« on: September 29, 2010, 05:42:17 PM »
Does anyone know if these are any good hulls?
10
Cars / Automobiles For Sale / Shelby GT500 parts--Kooks headers, complete KB 2.8 twin screw setup, 9" rear end
« on: September 24, 2010, 06:12:30 PM »
Shelby GT500 parts--Kooks headers, complete KB 2.8 twin screw setup, 9" rear end
Kooks custom headers (jet hot coated) with cats and H pipe. $850.00 for complete Kooks setup.
Also complete setup, KB 2.8 twin screw/ mammoth intake. sell for 4500.00 schmokin deal! Bolt in and go.
Have 725hp pump gas setup and 805rwhp pulley.
My car dynoed 670rwhp with the 91 octane tune and Kooks headers. The small pulley should be around 855rwhp with the smaller pulley.
Currie 9" housing with all Strange 35 spline components, ARB air locker, anti lock rings, aluminum driveshaft: only 900 miles on rear end assembly and it has not been to the drag races yet. ARB compressor still in box....install and go! $2200.00
Parts are getting removed this week.
Kooks custom headers (jet hot coated) with cats and H pipe. $850.00 for complete Kooks setup.
Also complete setup, KB 2.8 twin screw/ mammoth intake. sell for 4500.00 schmokin deal! Bolt in and go.
Have 725hp pump gas setup and 805rwhp pulley.
My car dynoed 670rwhp with the 91 octane tune and Kooks headers. The small pulley should be around 855rwhp with the smaller pulley.
Currie 9" housing with all Strange 35 spline components, ARB air locker, anti lock rings, aluminum driveshaft: only 900 miles on rear end assembly and it has not been to the drag races yet. ARB compressor still in box....install and go! $2200.00
Parts are getting removed this week.
11
Random Boat Parts For Sale / Re: WANTED BBF PARTS
« on: September 22, 2010, 12:48:16 AM »What pan are you looking for? Front/rear sump? HIgh Capacity Jet boat pan (Like a Dooley or the Milodon)?? I got a few laying around.....
Actually, scratch the Dooley, I forgot Rivertard has dibs on that one. Still got an extra Milodon though!
Ray
I need a high capacity jet boat pan. send me pic.
Thanks, Gordon
12
Engines / Engine Parts For Sale / Re: Looking for BBC rectangle port/open chamber heads
« on: September 20, 2010, 11:11:22 AM »
Thanks for the replies, but since i have found out this weekend the entire engine is junk, I think I am gonna put a Ford in it.
13
Random Boat Parts For Sale / WANTED BBF PARTS
« on: September 19, 2010, 07:45:32 PM »
Need BBF parts.
Looking for:
oil pan
motor plates/ bell housing--I may have some bought waiting on answer
A460 block
Blue Thunder heads with Chevy exhaust port if possible
blower manifold
flex plate
Headers
Looking for:
oil pan
motor plates/ bell housing--I may have some bought waiting on answer
A460 block
Blue Thunder heads with Chevy exhaust port if possible
blower manifold
flex plate
Headers
14
Random Boat Parts For Sale / Re: BBF Motor Plates
« on: September 19, 2010, 07:39:40 PM »
I'll take them; email me with info to paypal the money.
gordyd4@yahoo.com
I need these real bad!
gordyd4@yahoo.com
I need these real bad!
15
Engines / Engine Parts For Sale / Re: Looking for BBC rectangle port/open chamber heads
« on: September 15, 2010, 10:19:30 PM »
Ok, thanks for the education.
The gen 5 heads will work on my block also.
Do your prices include shipping?
The gen 5 heads will work on my block also.
Do your prices include shipping?
16
Engines / Engine Parts For Sale / Re: Looking for BBC rectangle port/open chamber heads
« on: September 15, 2010, 06:23:45 PM »
I don't know a lot about BBC engines, so bare with me. What are 990 heads?
My block is an older 4 bolt main truck block with the two piece rear seal.
My block is an older 4 bolt main truck block with the two piece rear seal.
17
Engines / Engine Parts For Sale / Re: Looking for BBC rectangle port/open chamber heads
« on: September 13, 2010, 10:18:41 PM »
Are they ready to install?
What's the difference between the two?
What's the difference between the two?
18
Engines / Engine Parts For Sale / Looking for BBC rectangle port/open chamber heads
« on: September 13, 2010, 12:48:47 AM »
I live in San Diego and am looking for a set of good cast iron BBC rectangle port/open chamber heads. I don't want to spend 2k on aluminum heads.
Thanks, Gordon
Thanks, Gordon
Pages: [1]