Null

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - flames

Pages: [1] 2 3
1
Engine Mechanical / Electrical / Thru Transom Basset Headers
« on: June 05, 2019, 06:01:19 PM »
Does any one have have any pictures of the water line setup beside the diagram also any pictures on the gate valves or bypass valves etc. I am getting ready to do my boat and need as much info as I can get.

460 motor basset thru transome exhaust with a thermostat kit.

Thanks in advance


Sent from my iPhone using SoCal Jet Boats mobile app

2
Engine Mechanical / Electrical / Re: BBF mini starter wiring
« on: May 14, 2019, 04:06:24 PM »
Currently I am not running a solenoid looks like I will have to run one now


Sent from my iPhone using SoCal Jet Boats

3
Engine Mechanical / Electrical / Re: BBF mini starter wiring
« on: May 14, 2019, 10:27:24 AM »
Here is a picture

4
Engine Mechanical / Electrical / BBF mini starter wiring
« on: May 14, 2019, 08:08:50 AM »
I am installing a mini starter on my boat. The stock starter has three wires red to the battery a tan and a yellow. The new starter has a place for 2 one is the battery. How do you wire this up or what wire do you use. I attached pics of old starter




Sent from my iPhone using SoCal Jet Boats mobile app

5
Jet Pumps / Re: PTO Drives
« on: September 14, 2018, 06:47:16 PM »
Quote from: bahner80 on September 12, 2018, 06:50:05 PM
Not all!!
I don’t have a pto either. Bolts straight to the crankshaft
That’s what I thought thanks


Sent from my iPhone using SoCal Jet Boats mobile app

6
Jet Pumps / PTO Drives
« on: September 12, 2018, 06:33:24 PM »
Do all jet pumps use a PTO before the driveline. My driveline doesn’t have a PTO adapter?


Sent from my iPhone using SoCal Jet Boats mobile app

7
Engine Mechanical / Electrical / BBF oil pan
« on: August 14, 2018, 10:35:41 AM »
What oil pan is everyone running I currently have a front sump which is bad. Also what is the best way to measure for space?


Sent from my iPhone using SoCal Jet Boats mobile app

8
Engine Mechanical / Electrical / Main Bearings
« on: August 13, 2018, 06:17:22 AM »
I have a BBF and it was just recently rebuilt less than 5 hours on it. Well had some issues this weekend and took it out and the filter had slot of metal shavings. Had my engine builder look at it and he found that the PTO shaft had a wobble and he said it could of taken out all the bearings has any one had this happen


Sent from my iPhone using SoCal Jet Boats mobile app

9
Engine Mechanical / Electrical / Thru Transom Exhaust fitment
« on: July 29, 2018, 05:29:21 AM »
My boat is a BBF and has log exhaust I am wonder if I switch to thru the transom headers do they line up with the current exhaust tip in the back of the boat


Sent from my iPhone using SoCal Jet Boats mobile app

10
Jet Pumps / Re: JF pump cavatating
« on: June 25, 2018, 05:41:06 AM »
Quote from: knotonduty on June 24, 2018, 07:13:21 PM
Prob should have it rebuilt. Just had mine done at D1performance Dane Fetherhoff.


Sent from my iPhone using SoCal Jet Boats
I had it rebuilt a couple summers ago


Sent from my iPhone using SoCal Jet Boats mobile app

11
Jet Pumps / Re: JF pump cavatating
« on: June 25, 2018, 05:40:32 AM »
Quote from: MillerKiller510 on June 24, 2018, 08:12:18 PM
How big is your boat

Sent from my SM-G955U using SoCal Jet Boats mobile app
It is a 21 mini day cruiser


Sent from my iPhone using SoCal Jet Boats mobile app

12
Jet Pumps / JF pump cavatating
« on: June 24, 2018, 04:25:21 PM »
I just had my motor rebuild and added some power it’s a full roller460 punched 60 over with dove heads. The problem is my stock JF pump cavatats now on take off the pump has very few hours on it and has a A impeller. Any suggestions or answers will help. Thanks


Sent from my iPhone using SoCal Jet Boats mobile app

13
Interior / Re: Interior coming along
« on: February 09, 2017, 09:14:08 PM »
I will get some more I believe mine is exactly the same as yours. Didn't you put a floor in yours? Do you have any pictures


Sent from my iPhone using SoCal Jet Boats

14
Gelcoat / Paint / Fireberglass Repair / Re: Leak
« on: January 19, 2017, 07:38:36 PM »
About done


Sent from my iPhone using SoCal Jet Boats

15
Interior / Re: Interior coming along
« on: January 19, 2017, 11:06:33 AM »
Thanks trying to figure out what to run on the motor cover. I have kids so I want a cover but I also want a scoop but not sure what looks best. Any pictures would be great


Sent from my iPhone using SoCal Jet Boats

16
Gelcoat / Paint / Fireberglass Repair / Scoop on motor cover
« on: January 19, 2017, 11:03:28 AM »
Does anyone have any pictures of scoops that you run on your boat with a cover over your motor I am undecided which way I want to go. I want a cover but I also want a scoop either fiberglass or aluminum


Sent from my iPhone using SoCal Jet Boats

17
Interior / Interior coming along
« on: January 14, 2017, 02:30:24 PM »
What do you think


Sent from my iPhone using SoCal Jet Boats

18
Engine Mechanical / Electrical / Ford 460 cam Roller setup suggestion
« on: October 12, 2016, 05:43:22 PM »
I am wondering what is a good setup. I have stock heads and would like to put a cam and roller setup in my motor I am looking for more performance.I am putting a victor intake and runing a 750 carbuerator. What is your suggestion lift size rocker arms ETC the more information the better. thanks

19
Gelcoat / Paint / Fireberglass Repair / Re: Leak
« on: May 21, 2016, 03:35:11 PM »
Almost ready


Sent from my iPhone using SoCal Jet Boats

20
Engine Mechanical / Electrical / Re: Carburetor Size
« on: May 01, 2016, 05:50:19 PM »
Is the motor stock


Sent from my iPhone using SoCal Jet Boats

21
Gelcoat / Paint / Fireberglass Repair / Re: Leak
« on: May 01, 2016, 05:48:59 PM »
Glass is almost done need to cut and set in floor. Making progress but running out of time. Almost boating time in Nebraska


Sent from my iPhone using SoCal Jet Boats

22
Engine Mechanical / Electrical / Re: Carburetor Size
« on: May 01, 2016, 05:33:21 PM »
What size carburetor should I run a 750 or 850


Sent from my iPhone using SoCal Jet Boats

23
Engine Mechanical / Electrical / Carburetor Size
« on: April 30, 2016, 08:06:34 AM »
I have a mostly stock 460 currently running a edelbrock performer intake and a edelbrock 750 Carburetor. I wanting to change carburetor but not sure on size I am switching to either a Holley or a quick fuel. Do I want a 750 or 850? Also considering switching intake to a victor intake. What are your thoughts? Thanks


Sent from my iPhone using SoCal Jet Boats

24
Gelcoat / Paint / Fireberglass Repair / Fiberglass mat on stringers
« on: April 27, 2016, 08:17:04 PM »
How many time do you cover your stringers with fiberglass mat and resin?  Also do you sand in between each layer? I have heard you don't have to sand.


Sent from my iPad using SoCalJetBoats mobile app

25
Hulls / Hole in bottom
« on: April 03, 2016, 02:58:57 PM »
 What is the best way to fix a hole in the bottom of a boat? I am replacing stringers and I put a hole in the hull when I was scraping the old fiberglass off.


Sent from my iPad using SoCalJetBoats mobile app

Pages: [1] 2 3

Null

SMFPacks CMS 1.0.3 © 2025