Null

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - SWIFTMIKE

Pages: [1]
1
Random Boat Parts For Sale / WTB stock Berk intake grate
« on: July 02, 2014, 04:16:09 PM »
Let me know if you have one please.  I'm located in Lake Elsinore.

Thanks
Mike

2
Jet Pumps / Advice on pump mods
« on: June 26, 2014, 06:29:47 PM »
Just picked up a spectra 18 and took it out for the first run last weekend.  Just looking for advice on what the trick setup on the pump on these might be.  Right now I have a BBC 454 that is mostly stock.  Pump is a Berk JC with a intake loader and place diverter.  Boat runs good to about 4k then it seems like the pump cavitates and I can't get anymore mph out of it but I have plenty of rpm left. 

3
Random Boat Parts For Sale / Parts
« on: May 07, 2014, 07:46:44 PM »
Oil Cooler $20
New blue cup Holders $10 pair
New Blue gauge bezels 1 4" and 4 2" all for $20
Nicson BBF front motor mount $40
BBF rear motor mount $40
New BBC gasket kit complete $50
I also have a bunch of Berkeley spare pump parts( c bowl, pump housing, impeller shaft, bucket, nozzle, shaft, transom cover) for sale so just let me know if you need something and make me an offer.  Please call or text Mike 9494128158

4
Engines / Engine Parts For Sale / BBF long bolt logs and snails
« on: May 07, 2014, 07:32:08 PM »
Big Block Ford long bolt logs and snails for sale.  $200 please call or text Mike 9494128158

5
Random Boat Parts For Sale / berk pump parts
« on: November 30, 2013, 08:30:16 PM »
http://orangecounty.craigslist.org/boa/4222204718.html
heres my craigslist add
please text me with any questions
thanks
mike 9494128158


6
Projects / 1974 Spectra 20
« on: August 12, 2013, 02:59:48 PM »
Hey guys....started on my spectra project finally!
I posted a project thread over on RDP in the spectra forums.

Here is the link.....check it out and let me know what you think.....I will be updating it as I go.

http://www.riverdavesplace.com/forums/showthread.php?100100-74-SPECTRA-20-PROJECT

Thanks
MIke

7
Project Boats For Sale / 74 eliminator bubble deck
« on: July 23, 2013, 08:38:11 PM »
GONE!!!!

Thanks
Mike

8
Gelcoat / Paint / Fireberglass Repair / Fiberglass question
« on: July 22, 2013, 07:20:04 AM »
Ok, so I am in the middle of replacing my transom and installing a Berkeley pump into my hull......my question is what glass and resin should I use to glass in the transom and what should I use to fill the hole where the pre existing intake for the pump was.  I have decided to stay away from epoxy resin just for cost.... I am just mostly interested in what weights of cloth/mat you recommend and  what would be the best process/material to seal that large hole from the intake so I have a fresh start for the new intake.

Thanks In Advance
Mike

9
Hulls / 75 Eliminator Bubbledeck questions
« on: June 19, 2013, 06:45:00 AM »
Ok so Ive been tearing apart my bubbledeck project hull and I have 2 questions for you guys.

1) The front of the hull is packed with foam.....is this necessary....and if so what do I replace it with?

2) There are a set of fins in the center of the boat(like a v drive)....not sure if these are stock or an aftermarket idea...should I keep them or ditch them?

Thanks
Mike

10
Miscellaneous / Spam / misc parts
« on: June 16, 2013, 03:42:11 PM »
ok heres a link to my craigslist add....everything is just obo or make me an offer

http://orangecounty.craigslist.org/boa/3875169534.html

few things listed:

jet pump, harmin eletronic trim adjust, thru transom exhaust flanges etc

take a look and let me know if you need anything

thanks

11
Jet Pumps / Set Back Pump
« on: June 14, 2013, 12:01:05 PM »
Just wanted to get everyone's opinion/input on an idea.

I had posted earlier that the boat that I had recently purchased came with a Drake pump.....after a lot of thought and advice from the pros im going to drop the Drake pump and replace it with a Berk JC that I have found.  My question is....if I am going to all the trouble to replace the intake and pump should I set it back?  I have read that it is not benefecial for every hull.  My hull is a 1975 Eliminator 18' Bubbledeck....if I should set it back my second and third question is how far back and should I set the motor back or leave it?

Thanks in Advance
Mike

12
WTB / glass and epoxy
« on: June 06, 2013, 08:30:22 AM »
If anyone has leftover epoxy resin and glass mat they are willing to part with let me know

Thanks
Mike

13
Jet Pumps / Drake Pump
« on: June 05, 2013, 09:25:45 AM »
Hi everyone....I'm new to the forum! I have just recently purchased my first boat...and its a huge project!  I will start a project thread as soon as I start tearing into it.  The boat came with a Drake pump....which from doing some research I understand is hard to find parts for and any information about.  I would like to basically be able to completely rebuild the pump but I dont even really know where to start.  Im just trying to see if anyuone here has any extra parts, manuals, knowledge, advice......etc.  I understand most of you will probably suggest I replace it with a Berk....but its just not in my budget...and I figure since I'm a machinist and have access to machines.....I can just make the parts I cant find.  Let me know what you guys think.

Thanks
Mike

Pages: [1]

Website Security Test
Powered by EzPortal

anything
Website Security Test