I have a freind from high school in Oklahoma thats coming out to Phoenix to drag boat race. He is currently 1st in his class, his name is Jeff LaBlanc and his boat is Blown Crazy. He is in need of sponsership or help since this is 1000 miles here and 1000 miles back. Any little bit would help. If you could sponsor he can get your name or business name in the annoucer book. If interested pm me and i can get you his number. Thank you

I am running out of ideas, I have a 98 Z71 4x4 and driving in 2 wheel drive it makes a growl noise from the front end after about 40mph, put in 4 high and it goes away and stays away when going back to 2 wheel dr. when in 2 wheel it does not drive like its in 4 wheel so I know it is not stiking in 4 wheel dr. Is this a common problem with these? it has 115k on it. Other then that it runs good, shifts good, etc.  Any ideas will help.

I have a problem with stalling after running for 30 to 60 seconds at about half throttle. Changed a few things and woke up in the middle of the night thinking its running out of fuel.  Idles all day long and after it dies give it a few seconds and it would start back up, idle, and then go again for about 30+ seconds then die. idle all the way back to the dock.  I changed the fuel filter and moved fuel pressure guage where I can turn around and see it.  Ran much better almost without dieing but any more than half throttle and fuel pressure goes to 0 and then starts to sputter then I let up on throttle and fuel pressure climbes to about 2 to 3 and will run all the time, floor it again and pressure goes to 0 and does it all over again. Im thinking fuel pump. at idle it pumps 6psi all day but cant keep up when cruising, is it normal for the fuel pressure to go all the way to 0? I don't think it should and thinking of replacing electric pump with a carter p4070. Anyone use that one before? Or should I do Holley Red? right now im running what it came with and that's a facet noisy electric and dont really want to do that one again.or if there are any other suggestions/brands that may be better

I rebuilt my holley carb and was installing a plate that holds the throttle cable and when I tightened down carb I broke off the tab on the base plate I don't know if this can be welded back or see if I can find a base for a 3310.... I wanted to go to the lake but now I can't....what to do, what to do......

I am installing a place diverse on a JC Berk and I wrestled with it all day and still not complete. The pins that hold it to the bowl, the top one is too long but that ain't all. The holes for the place diverter were stripped, I tapped them and conquered that. Come to find out it was a hydraulic place D and the cable that was sent won't mount I'm the hole on the arm for the tilt. I know others have converted from hydraulic to manual. The cable is like a throttle cable  and don't have the big nuts like the reverse bucket cable. What do I do now?

I am wanting to replace factory Chevy Z-28 intake for BBC this winter and I can get a Edelbrock Victor Jr. 454-o from a friend but what I read about it it recommends 850cfm carb with I only have a 3150 holley which I believe is a 750. Will that be ok? I didn't want to buy a bigger carb too to do this or should I see about a different manifold and which is better single plane or dual?

I have a mildly built 454 BBC bored out 30 over and good cam and O/T Headers.  I am going to replace factory alum intake to a nice polished air gap one.  Should I go single plane or dual plane and why?  I know one is good for higher RPMS than the other but I am  only turning about 5000 rpms

I'm from Moore Oklahoma, graduated from Moore High School and lived a mile north from where toronado hut. I know zilla68 lives there but can't get in contact with him. I hope him, his family, and jet boat are ok.

Sent from my DROID RAZR using SoCalJetBoats mobile app

I noticed I have rusty water in my pool light. Is this a shock hazard? Do you just take light out and unscrew old bulb and screw in new one? I noticed LED bulbs don't, they are rewired and does anyone know how to re wire if i go this route. I know wiring just wondering if there is anything special since this is underwater.

Finally got around to installing the HD carpet and used there glue with excellant results!

Going to be installing new carpet in week or so as soon as the humidity goes back down. What is a good carpet glue, the Home Depot indoor/outdoor carpet glue or should I spriong for the caarpet glue at West Marine?  Any thoughts or ideas?......

I took my boat to lake this weekend and never had trouble starting so I did not run at home before leaving.  Got to lake and it did not start or would sputter and die and not resart.  Gas smells like varnish and it has been in there since fathres day weekend.  Do I need to drain and fill with freash gas, or is there an additive that I can pour in to get it to burn and do I need to rebuild holley carb while im at it?