1
Random Boat Parts For Sale / Re: Sand spikes
« on: June 08, 2021, 08:35:42 PM »
I sent you a pm
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Random Boat Parts For Sale / Re: Sand spikes
« on: May 04, 2021, 03:02:27 AM »
I'd like 2 of them if still available?
3
Engines / Engine Parts For Sale / Re: Ford 460 Harman Marine Thru Bolt Exhaust Logs & Snails
« on: September 22, 2020, 10:28:50 AM »
Here they are:
[/URL]
[/img]
[/URL][/img]
[/URL][/img][/URL][/img]
4
Engines / Engine Parts For Sale / Re: Ford 460 Harman Marine Thru Bolt Exhaust Logs & Snails
« on: September 20, 2020, 01:06:08 PM »
I've got a nice set of those for sale. $500 + ship
5
Engines / Engine Parts For Sale / Re: Big Ford engine mounts
« on: September 20, 2020, 01:04:14 PM »
What is the piece in the very center of that water block off plate? have not seen that before
6
Engine Mechanical / Electrical / Water Routing for Center Riser Exhaust
« on: September 06, 2020, 01:36:50 AM »
I finally found some exhaust manifolds that match up with the transom holes for repowering this boat from a 455 to a 460.
However, the riser water line requirements seem to be different than the standard logs with jugs. I want to have the Berkley feed water into the manifold so it gets pre-heated before entering the engine, but there is no return line port like the typical jugs have. Can somebody tell me how to route the cooling water so it can be pre-heated first?
However, the riser water line requirements seem to be different than the standard logs with jugs. I want to have the Berkley feed water into the manifold so it gets pre-heated before entering the engine, but there is no return line port like the typical jugs have. Can somebody tell me how to route the cooling water so it can be pre-heated first?
7
Fabrication / Custom Swim Step
« on: July 17, 2020, 01:08:52 AM »
Where does everybody go to have a custom swim step made?
I checked out what Eddie Marine offers and it's nice, but I'd have to TIG 2 of their steps together to span my transom.. would rather just get something made right the first time.
I checked out what Eddie Marine offers and it's nice, but I'd have to TIG 2 of their steps together to span my transom.. would rather just get something made right the first time.
8
Interior / Where can I get a waterproof glove box
« on: July 17, 2020, 12:22:46 AM »
Looking to install a water proof locking glove box in the center of the dash for storing wallets and cell phones.
Rough dimensions are 12" x 6"
Rough dimensions are 12" x 6"
9
Engines / Engine Parts For Sale / Re: Bassett Headers for F460
« on: May 17, 2020, 04:12:34 PM »
bump
10
Engines / Engine Parts For Sale / Re: Looking for bbf parts
« on: May 06, 2020, 06:53:14 PM »
I've got some BBF OT ceramic coated headers available for $500
11
Engines / Engine Parts For Sale / Bassett Headers for F460
« on: March 04, 2020, 06:37:09 PM »
Ceramic coated.
I don't have any other plumbing available for these, since I never mounted them in my boat:
$500 for the pair plus shipping.
I don't have any other plumbing available for these, since I never mounted them in my boat:
$500 for the pair plus shipping.
12
Engines / Engine Parts For Sale / Re: BBF Headers WTB
« on: February 12, 2020, 11:20:11 AM »
I've got a set of Bassett BBF over transom headers available
13
Engine Mechanical / Electrical / Re: Dumping 455 and installing an F460 - exhaust plumbing help
« on: October 30, 2019, 12:42:29 PM »
Called Eddie Marine today to inquire about the center riser style manifold, which would definitely solve my problem. Unfortunately they only make this for SBC and BBC......this is so frustrating!
14
Engine Mechanical / Electrical / Re: Dumping 455 and installing an F460 - exhaust plumbing help
« on: October 29, 2019, 01:16:09 PM »
Are you saying put the long bolt manifold snails on the regular manifolds? This would gain me about 1/2" in height I think.
15
Engine Mechanical / Electrical / Re: Dumping 455 and installing an F460 - exhaust plumbing help
« on: October 28, 2019, 12:58:38 PM »
So I bought those Hardin Long Bolt manifolds and they are really nice, but unfortunately they make my problem worse because the runners slope downward.
Anybody have some other ideas?
Anybody have some other ideas?
16
Engines / Engine Parts For Sale / Windshield for sale
« on: October 28, 2019, 12:55:37 PM »
I'm in Seattle.
This came off a 16ft boat I believe.
Make offer
This came off a 16ft boat I believe.
Make offer
17
Engines / Engine Parts For Sale / 455 parts
« on: October 28, 2019, 12:52:54 PM »
I'm in Seattle.... make offer
I have both risers, even though just 1 is pictured. I do not have any other 455 parts left.
I have both risers, even though just 1 is pictured. I do not have any other 455 parts left.
18
Engines / Engine Parts For Sale / Center Rise Exhaust Manifolds needed - BBF
« on: October 28, 2019, 10:27:16 AM »
I've tried standard hardin logs and hardin long bolt logs, but the snail exit doesn't match up with my existing transom holes. I guess I need some center riser exhaust manifolds from somebody like Edde marine?
I think these must be what I need?
I think these must be what I need?
19
Engine Mechanical / Electrical / Re: engine mounting question. I have bad vibration coming from the drive shaft ?
« on: October 20, 2019, 11:13:09 AM »
Post up some pictures of your setup so we can help.
I've got an F460 with 12JE setup, Milodon 8" 10qt pan, 4 point mounting system and everything lines up nice (except my exhaust to transom ports).
I've got an F460 with 12JE setup, Milodon 8" 10qt pan, 4 point mounting system and everything lines up nice (except my exhaust to transom ports).
20
Project Boats For Sale / Re: 19’ Spectra
« on: September 22, 2019, 01:29:34 PM »
How much for the saddle tanks (if you're willing to separate)?
21
Engine Mechanical / Electrical / Re: Cracked Snail Riser
« on: September 22, 2019, 01:11:45 PM »
I just took one of my snails off to replace the leaking gasket. The log had some serious gouges in it (might have been from me wrestling the snail off). You can fill the area with jb weld, slap a new gasket on it, and let it cure in a vise with the snail pointed toward the ground so jb weld doesn't run too deep into the cooling passages. I've got jb weld in the 4 cooling passages, but no thicker than .25" deep.
22
Engines / Engine Parts For Sale / Re: BBF Exhaust Manifolds
« on: September 20, 2019, 12:37:30 AM »
Did these sell?
I need a set just like that for my F460 project
I need a set just like that for my F460 project
23
Engine Mechanical / Electrical / Re: Dumping 455 and installing an F460 - exhaust plumbing help
« on: September 13, 2019, 12:01:34 AM »
I was hoping there were a few different types of Hardin Logs for an F460 so I could simply change the manifold or the snails.
I have a set of Bassett headers, but they also run into the transom
I have a set of Bassett headers, but they also run into the transom
24
Engine Mechanical / Electrical / Re: Dumping 455 and installing an F460 - exhaust plumbing help
« on: September 11, 2019, 12:34:58 AM »
I would say that my logs are about 2" below the transom holes and about 9" apart on the port side. I used some lithium grease and stuffed the port side hose on, but you can see the angles that are pulling away. The other side the distance looks more like 5". Are Hardin logs identical on both sides of the motor, or do they have a left and right side that will account for the exhaust port offset?
I tried MIGing up a little adapter pipe that could account for the 2" offset, but this is the easy side..... I don't see any way to pull this off on the hard side.
Lastly, does anybody have an upper Ujoint cover available for sale?
I tried MIGing up a little adapter pipe that could account for the 2" offset, but this is the easy side..... I don't see any way to pull this off on the hard side.
Lastly, does anybody have an upper Ujoint cover available for sale?
25
Engine Mechanical / Electrical / Dumping 455 and installing an F460 - exhaust plumbing help
« on: September 09, 2019, 10:19:51 PM »
New to the forum, so go easy on me please.
Trying to revive a 1976 Caldwell 19ft boat with a Berkley 12JE. The boat originally came with a 455 and 3 point mount. I received the boat with nothing but the pump in it.
I sourced a late model f460 and installed with a 4 point mount and Hardin exhaust logs. Now for the dilemma......
My transom exhaust ports are a few inches off from where the Hardin log exhaust ports sit when bolted to the F460. I tried to flex the rubber exhaust hose, but it's too rigid for the short rise/run distance I'm trying to adapt.
I know many people have dumped the 455 and converted to 454 or 460, so what do they typically do about the pre-existing transom holes?
Trying to revive a 1976 Caldwell 19ft boat with a Berkley 12JE. The boat originally came with a 455 and 3 point mount. I received the boat with nothing but the pump in it.
I sourced a late model f460 and installed with a 4 point mount and Hardin exhaust logs. Now for the dilemma......
My transom exhaust ports are a few inches off from where the Hardin log exhaust ports sit when bolted to the F460. I tried to flex the rubber exhaust hose, but it's too rigid for the short rise/run distance I'm trying to adapt.
I know many people have dumped the 455 and converted to 454 or 460, so what do they typically do about the pre-existing transom holes?
Pages: [1]
