Null

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Btcampbell

Pages: [1] 2
1
Jet Pumps / Re: Prime a jet
« on: July 07, 2022, 09:04:53 am »
No it?s a prime a jet drilled into the bowl. I just called HTP and they told me at idle it?s normal and should shut off on throttle.

2
Jet Pumps / Prime a jet
« on: July 07, 2022, 08:39:04 am »
Hello y?all, I have a prime a jet on my Berkeley pump and noticed water sprays out of the two jet holes while running. Is this normal? I was just wondering if it closed off some how or it?s supposed to spray out.  Thanks

3
Hulls / Re: Transom
« on: March 15, 2022, 07:08:29 am »
What make hull do you have? Eliminator I?m guessing. Mine is a kustomKraft tx19. First time I?ve seen one without wood. Thanks

4
Hulls / Transom
« on: March 14, 2022, 09:52:34 am »
Has anyone seen or have a hull that does not have any wood on transom?

5
Hulls / Re: Nordic
« on: May 13, 2021, 08:02:06 am »
Thank you

6
Hulls / Nordic
« on: May 05, 2021, 07:13:13 am »
Anyone have any input on Nordic v hull.  Good or bad

7
Jet Pumps / Re: Berkeley ig pump
« on: April 27, 2021, 10:06:07 am »
Will do. Reckon a bowl inspection is in order. Thanks for the info. This is my first jet boat as you can tell, lot of things to learn. 

8
Jet Pumps / Re: Berkeley ig pump
« on: April 27, 2021, 03:58:06 am »
Dang sgriffin!  So today I checked the bowl grease,(90wt) and it seems low or empty. Only been out twice on 30 or 45 min runs. I filled it back up and it didnt take very much. How much does it take to fill when empty. Sorry for all the questions.

9
Jet Pumps / Re: Berkeley ig pump
« on: April 26, 2021, 06:14:33 pm »
I don’t know about loader or inducer

10
Jet Pumps / Re: Berkeley ig pump
« on: April 26, 2021, 05:55:04 pm »
Yes for the block cooling. I was told it is a stainless impeller

11
Jet Pumps / Re: Berkeley ig pump
« on: April 26, 2021, 04:31:04 pm »
Gauge on intake manifold. Thanks Flusher, yea your probably right just tired.

12
Jet Pumps / Re: Berkeley ig pump
« on: April 26, 2021, 11:05:51 am »
If I’m moving and hit it,seems to do fine. Also noticed at idle there is no pressure showing on my gauge the goes up to about 20 or 30 when I accelerate

13
Jet Pumps / Re: Berkeley ig pump
« on: April 26, 2021, 09:53:46 am »
I just got it as a hull in September (mantra tunnel), just got a motor in it (496 bbc), wiring, etc. well you probably know what I’m talking about. I’ve only had it out twice. I did hit the grease fitting about 4 pumps and topped
Off bowl with marine grease

14
Jet Pumps / Berkeley ig pump
« on: April 26, 2021, 03:47:36 am »
What do y’all think is the problem? If I stomp on it from a stop it feels like pump slips, almost like a clutch slipping in a car????? Sometimes when idling it makes a rattling noise.

15
Gelcoat / Paint / Fireberglass Repair / 5/16 hole thru hull
« on: February 17, 2021, 05:05:56 am »
Hey fellas how do I fix a 5/16 holes that have been drilled thru hull. Someone did this to mount the seats and I want to repair them and mount with aluminum angle on stringers. Thanks

16
Engine Mechanical / Electrical / Re: O/T Headers
« on: October 15, 2020, 05:48:01 am »
Yes I do have a exit. CP sells a dump port with a built in pressure relief valve, has anyone tried one of these?

17
Engine Mechanical / Electrical / O/T Headers
« on: October 14, 2020, 08:46:24 am »
What is the best way to plumb the cooling lines for engine when running dry headers? Do I need to run a pressure relief dump? 

18
Hulls / Re: 1988 mantra tunnel
« on: September 20, 2020, 12:58:25 pm »
Hot foot bracket

19
Hulls / Re: 1988 mantra tunnel
« on: September 20, 2020, 11:37:06 am »
I have seen in pics of boats the accelerator peddle is attached to a bar that is mounted between the stringers, does a company sell them? I would like to do this to mine

20
Hulls / Re: 1988 mantra tunnel
« on: September 20, 2020, 04:53:54 am »
Is that your boat in your avistar? Looks nice! Is it a tunnel hull

21
Hulls / Re: 1988 mantra tunnel
« on: September 19, 2020, 06:39:34 pm »
Hey I appreciate the responses, just trying to get all the info I can. Not trying to break any speed records, just wanting a little ripper for around the home lake.  Lol

22
Hulls / Re: 1988 mantra tunnel
« on: September 19, 2020, 05:14:45 am »
Now ya got me worried! No its measures 16.6 ft. From what I have found it is an old drag boat. Its got a berkeley 12JG/ R pump on it. I'm just wanting to run 60 or 70 mph

23
Hulls / Re: 1988 mantra tunnel
« on: September 18, 2020, 02:55:54 pm »
T

24
Hulls / Re: 1988 mantra tunnel
« on: September 18, 2020, 02:52:01 pm »
Some more pics. Gotta scrounge up a motor now

25
Hulls / Re: 1988 mantra tunnel
« on: September 18, 2020, 07:17:17 am »
Here are some pics from add

Pages: [1] 2

Null

SMFPacks CMS 1.0.3 © 2022