101
The No Wake Zone / Re: Who's drinking what tonight?
« on: February 20, 2008, 02:50:01 PM »
Im startin early with som Sailor Jerries and coke. Good stuff, 92 proof. 
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
102
WTB / Re: rail kit motor plates
« on: February 20, 2008, 01:46:57 PM »
I've got the tools to do it, just don't know where to begin. Wanna come over and show me Ralph? I got some beers in the fridge. lol
~Brian
~Brian
103
Engines / Engine Parts For Sale / Re: BBC Exhaust Logs Harman Marine
« on: February 20, 2008, 01:45:25 PM »
how much and what size outlet on the snails?
~Brian
~Brian
104
WTB / rail kit motor plates
« on: February 20, 2008, 09:28:10 AM »
Im looking for a set of motor plates so I can build a rail kit for my boat. Its a bbc. Thanks a bunch!
~Brian
~Brian
105
Engines / Engine Parts For Sale / Re: ISKY 640 Roller Cam
« on: February 19, 2008, 04:39:56 PM »
yes but I'm using them for another cam profile. This is the cam only. Rollers are cheep tho.
~Brian
~Brian
106
Boats For Sale / Re: blow out sale 2000.00
« on: February 19, 2008, 02:26:51 PM »
got any pictures?
107
Engines / Engine Parts For Sale / Re: ISKY 640 Roller Cam
« on: February 19, 2008, 02:19:23 PM »
mark IV
108
Boat Showcase / Re: Lets See Your Rides
« on: February 19, 2008, 10:09:52 AM »
Thanks for the welcome!
109
Boat Showcase / Re: Lets See Your Rides
« on: February 18, 2008, 08:59:24 PM »
my ride is the green one on the right. 
~Brian
~Brian
110
Engines / Engine Parts For Sale / ISKY 640 Roller Cam
« on: February 18, 2008, 08:06:03 PM »
I have an ISKY cam Im not going to use. Its for a roller setup heres the specs.
Duration, 318 deg
Open 51 Before TDC
Close 87 After BDC
Cam lift .371
Valve Lift .650
Valve Lash .028 Hot
.30 Cold
Exhaust timing.
Duration 318 deg
Open 87 Before BDC
Clost 51 after TDC
Cam lift .371
Valve lift .650
Valve Lash .028 hot
.030 cold
Lobe Center 108 Deg. Overlap 102 Deg Cam Advance 0 Deg
The above timing is checked aat .020 Open lifter rise
.020 (close
Intake Duration 272 open before TDC @ 28 and close after BDC @ 64. For the exhaust 272 duration open 64 before BDC and close @ 28 After TDC.
100 bucks. I drive from San Bernardino to San Luis Obispo once a week so if your on my route I can drop it off at your pad. Would go great with a set of closed chamber heads and some compression. Clean it up and run her. Lopity Lope! (edit, its for a bbc just FYI)
~Brian
Duration, 318 deg
Open 51 Before TDC
Close 87 After BDC
Cam lift .371
Valve Lift .650
Valve Lash .028 Hot
.30 Cold
Exhaust timing.
Duration 318 deg
Open 87 Before BDC
Clost 51 after TDC
Cam lift .371
Valve lift .650
Valve Lash .028 hot
.030 cold
Lobe Center 108 Deg. Overlap 102 Deg Cam Advance 0 Deg
The above timing is checked aat .020 Open lifter rise
.020 (close
Intake Duration 272 open before TDC @ 28 and close after BDC @ 64. For the exhaust 272 duration open 64 before BDC and close @ 28 After TDC.
100 bucks. I drive from San Bernardino to San Luis Obispo once a week so if your on my route I can drop it off at your pad. Would go great with a set of closed chamber heads and some compression. Clean it up and run her. Lopity Lope! (edit, its for a bbc just FYI)
~Brian
111
Engine Mechanical / Electrical / Re: Heads
« on: February 18, 2008, 04:20:50 PM »
Yeah, the timing chain was out of phase. I don't know about compression I didn't check but I want the engine to stay together for a while so while its apart I better take care of everything.
~Brian
~Brian
112
Engine Mechanical / Electrical / Heads
« on: February 18, 2008, 03:51:24 PM »
I pulled apart my engine today to find out that my intake valves have touched the pistons. So I am going to have to have the heads gone through. Who have you guy's used with good results here in the IE? Thanks for the heads up!
~Brian
~Brian