51
Project Boats For Sale / Re: free raysoncraft flatty
« on: November 26, 2010, 05:16:58 pm »
where u located at i kinda need something to do this winter im board ran out of projects
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
52
Boats For Sale / Re: What to look for/look out for when buying a boat?
« on: November 18, 2010, 06:40:02 pm »
when i was looking for a flottie all i looked for was thick hual and a deck willing to put up with a few honeys dancein on it without failure and all the rest of the stuff these guys said 
53
Boats For Sale / Re: Hallett 19SS
« on: November 18, 2010, 06:28:07 pm »
very nice hallet i love mine way to much to sell it
54
Sand / where to go glamis or orgon or sand mt NV
« on: November 18, 2010, 06:17:44 pm »
me and my friends have never been to any sand other than pismo and thats gay so from where we live glamis orgon and sand mt are about the some distince from us so the question is where do we go hope u guys can give so good feed back and help our dission
55
Sand / Re: Desert Season
« on: November 18, 2010, 06:11:26 pm »
oh ya desert season for sure dust of the bikes and jaw bone canyon here we come me and my hill climbing junkie pals try to go at least once a month if not twice or out to carnagie its good for climbin 
56
Projects / Re: Pat's Tunnel Project
« on: August 03, 2010, 08:25:30 pm »
i got a friend that finds deals like this all the time hes getting tierd of that kinda shit to i feel for u man
57
Engine Mechanical / Electrical / Re: Need Advice... Had shop rebuild carbs, now runs poor and gas in oil...
« on: August 03, 2010, 08:18:15 pm »
totally sounds like base to body gasket just letting fuel flood in every time it dies ive seen it before i had a demon do it and a holly they were both the same dang thing drove me nuts till i found what was up 
58
Engine Mechanical / Electrical / Re: Need Advice... Had shop rebuild carbs, now runs poor and gas in oil...
« on: August 03, 2010, 05:52:49 pm »
me and a friend rebuilt his carb on his daycruzer had all the some semtoms we found that we had put the wrong gasket in the base because the right one didnt fit right that wrong gasket let the fuel bowls emty into the motor after it was off and while running it bypassed and flooded it made it run like shit
59
Engine Mechanical / Electrical / Re: bad cam walk
« on: August 02, 2010, 08:59:21 pm »
that sucks didnt know that so i just f@#ked myself thanks for the info
60
Projects / Re: cav plats on my jet
« on: August 02, 2010, 08:36:57 pm »
i think 76 my picture taker went swiming working on that problem got pics on my my space im peck from mariposa on there if you want to see pictures right this second sorry man
61
Engine Mechanical / Electrical / Re: bad cam walk
« on: August 02, 2010, 08:32:55 pm »
i used a good steel timeing set all brand new parts its an isky cam but when it walked back the edge of the rollers on the lifters kinda wore a line in a few off the lobes the lash was set at 17 and 19 thats what the cam card wanted idk ive had a few people alot smarter then trying to help as for the block it wore the flat part on the back off the timeing gear wore into the block and ate the cam bering groove in tthe block is about 16th to 1/8 deep i only ran the motor on the lake for a couple hours then noticed the shiney stuff in the oil if reparible would any machine shop be up for the task
62
Engine Mechanical / Electrical / bad cam walk
« on: August 01, 2010, 09:25:35 pm »
ok got bbc with a big roller cam its got bad cam walk to the rear and it damaged the block is this fixiable i dont know why the cam walks so bad ive never seen one walk back its always been foward thats y theres a button right
63
Engine Mechanical / Electrical / Re: Squished Headers...
« on: August 01, 2010, 09:19:43 pm »
if the boat is lean this this could happen ive seen one of my friends racecars melt through from being to lean but it also killed the motor we always run the motor full bore and shut it off without leting it idle and pull plugs look for coco brown thats ideal some guys like them a little whiter than that but u dont want white that could be fatele thats how i did mine theres probly a better or easyer way but i wouldnt know
64
Gelcoat / Paint / Fireberglass Repair / Re: finding hedders for my hallet
« on: August 01, 2010, 09:07:18 pm »
its a big chev i guess a could put some kind of heat sheld on them that would probly work
65
Projects / cav plats on my jet
« on: August 01, 2010, 09:00:12 pm »
hey whats up ? ive got full cav plats on the back of my hallet never messed with them what should they be set at the same as a v drive or because its jet should it be diffrent
66
Gelcoat / Paint / Fireberglass Repair / finding hedders for my hallet
« on: July 29, 2010, 06:42:27 pm »
im haveing trouble finding ot headers for my hallet the back is really narrow and every set ive tryed all came within a pinky size of touching the fiberglass any ideas that wound help me i just dont want to buy ones that are going to burn my shit up someone said twisteys might work but idk
67
WarZone / Re: New Motivational Posters…
« on: July 29, 2010, 06:26:47 pm »THAT IS AWSOME, remember, an ehxhaust tip and a wing does not make it a race car!ya and they think they can drive