SoCal Jet Boats
Tech Talk => Projects => Topic started by: thekraziestdago on April 23, 2010, 01:14:16 PM
-
So i bought this boat off of my Uncle because I love this boat and practically grew up on it, the only problem is my uncle half assed fixing it and he really DIDN'T TAKE CARE OF IT.
So im planning on getting it looking good before the end of this yea.
So it's a 19' 79 Cole with a BBC AND Berkeley Pump
PROBLEMS
- the hulls needs some work, the dash is cracked and the deck has a shit load of ( it looks like little 1'' chips or cracks) o and a paint job
-it doesnt have a splt bowl and place diverter and i think the pump need to be rebuilt
- stringers need to be replaced
- needs new upholstry
- motor needs work
- trailer needs new bunks, paint and wiring
I'm not sure where to start or what exactly what to do.
HELP WOULD BE GREATY APPRECIATED
-
That's quite a list you have there. For your pump, I'd go to Cyclone Marine, Jim Brock, he's in Pacoima right off the 118 and Glenoaks. The stringers and gel work could be handled by a number of folks, GS Marine in Corona is a good shop.
Why do you say the stringers need replaced? Put up some pics of the stringers.
-
Looks like a pretty boat! Good luck with the rebuild. Yeah, get some pics up of what ya got to work with. Someone'll be able to help. I'm in the middle of diggin fiberglass out of orificies I didn't know existed...... :screwy:
But looks like you're on the right track by gutting it and just goin in balls deep!
From the engine, looks like a good foundation, although that tunnel ram I don't think I've seen before. ::)
I wouldn't worry about the whole split bowl thing. Seen PLENTY of non split bowls run very hard and toss out a monster roost. Just need a Place Diverter is all. :thumbup:
Ray
-
With a list like that the first thing I would do is find another boat with a shorter list! >:D
-
Yeah That's a long list, My list was very similar just 2 months ago and now it's much shorter. Read up on the information in these forums, Watch a lot of U-Tube video's on do it yourself boat projects, Ask questions
here and just keep at it and later then you think after spending more then you thought it will still need more work and still not be done.. :banghead: :mad: But keep at it like your :screwy: And eventually you
will have a super Cool Boat, Good Luck and post more pics, I'm a few steps ahead of you so feel free to ask.. Roy
-
ok so i went home and took more pictures i might have over reacted a little on the stringers, but where the motor mounts meet the stringers the stringers are pinched and there are holes under neath the seats.
but this is what i got.
ooooo and fortunately my dad was a master mechanic and he raised me right, when i do something i go through everything cause i hate to be that guy stranded on the lake with a dead boat no beer and prayin for a tow.
-
The stringers don't look to be a problem. You might want to look into installing a rail kit for mounting the engine.
The crack can be repaired. There are a couple threads here with good pics of dash repairs.
The upholstery isn't too expensive if the wood is saveable.
I'll look around an see if I can post some links to the threads you need to see.
-
ok so where can i get a rail kit, and what can i use to clean the stringer, fill the holes and get them looking into better condition.
and if i use the rail kit will i still be able to use the motor mounts that i got right now.
-
Rail Kit:
http://www.socaljetboats.com/random-boat-parts/rail-kits-bbc-sbc-460-ford-455-olds/msg85468/#msg85468
Cracked Dash:
http://www.socaljetboats.com/gelcoat-paint-fireberglass-repair/cracked-dash/msg105152/#msg105152
Upholstery:
http://www.socaljetboats.com/interior/upholstery-in-the-inland-empire/msg16376/#msg16376
Good luck with the build ;D
-
they frames for the seats are fallin apart there just chunks of wood all over the floor boards, and the frames were never resined so they were just bare wood.
thanks for all the helpul hints and advice i appreciate it.
here so more pics
-
welcome to the site :thumbup:
good looking boat
-
Stringers don't look bad to me either. Should be GTG on it! Seat frames are easily made. Someone on here even made his outta composite decking wood, kinda cool.
PM Ironman here on the boards for a rail kit. He custom makes them :thumbup:
Ray
-
So ive been doing a lil reseach to get the pump rebuilt with all the bells and whistles, so to have the pump gone through by
jet boat performance in atascadero (split bowl ,bronze prop, place diverter, droop snoot)would cost me about $2519
and thats for me to pull the pump, does this sound like a reasonable price
-
Unless you're going to be putting some serious HP into this thing you don't need a bronze impeller.
-
Unless you're going to be putting some serious HP into this thing you don't need a bronze impeller.
What do you consider "Serous HP", I'm under the belief that bronze/SS are needed for 450 HP +. Am I correct?.. Roy
-
I couldn't find what I was looking for but what I had read or was told was...
Aluminum = up to 550-600HP without problems
Bronze = up to 800-900HP without problems
Stainless = anything over 800HP
I'm sure people have run higher HP on the aluminum/bronze, but why take a chance?
450hp is not much over a mild build for a jet.
-
Aluminum = up to 550-600HP without problems
Bronze = up to 800-900HP without problems
Stainless = anything over 800HP
I'm sure people have run higher HP on the aluminum/bronze, but why take a chance?
450hp is not much over a mild build for a jet.
Your Numbers are slightly higher then I was being lead to believe but we are real close, So close I'm sticking to my plan to not touch my pump/alum impeller till the 500ish HP engine is in and bugs worked out, Then diverter/bronze impeller and only then add the NOS that will give me bursts a little over 600 HP.. Thanks for the info makes me confident in my plan... Roy.