Let's see your trailer rims

« **Reply #25 on:** April 15, 2015, 05:16:25 PM »

Quote from: Mrblueeyesnick on April 15, 2015, 12:37:01 PM

I just have the good ol' fashion domes

Sent from my garage drinking a cold PBR

I wish mine still looked this good. I wouldn't be looking for new rims.

« **Reply #26 on:** April 15, 2015, 06:04:18 PM »

Quote from: el mojado on April 15, 2015, 05:16:25 PM

I wish mine still looked this good. I wouldn't be looking for new rims.

It took a lot of time to get those looking like that. I had to hammer out a few dents in the domes and went though a lot of windex and ultra fine steel wool but they turned out nice.

Sent from my iPhone using SoCal Jet Boats

« **Reply #27 on:** April 15, 2015, 06:55:51 PM »

eBay special.

Sent from my iPhone using SoCal Jet Boats

« **Reply #28 on:** April 15, 2015, 06:57:35 PM »

19" TRD with 10" fenders

« **Reply #29 on:** August 04, 2015, 11:06:57 AM »

67 US indy mags 15x7

Sent from my iPhone using Tapatalk

« **Reply #30 on:** August 04, 2015, 11:36:03 AM »

17" American Racing wheels, Torq thrust II, on Chevy hubs.

« **Reply #31 on:** August 04, 2015, 01:46:32 PM »

Can't believe I am showing my nuts!

« **Reply #32 on:** August 04, 2015, 01:52:49 PM »

I would think those low profile tires would be pretty rough on the hulls.

Sent from my iPhone using SoCal Jet Boats

« **Reply #33 on:** August 04, 2015, 04:23:42 PM »

Well you know the older one gets the lower they............oooh well.

« **Reply #34 on:** August 04, 2015, 05:09:54 PM »

Very nice totes gentlemen. I'm towards the end of a total rehab on my old Gireaux trailer, wide fenders, lights and powder coating. I went old school to go with our boat-Supremes in a 15 x 7 with 225/60/15 radial TA's.

Steve-O

« **Reply #35 on:** August 04, 2015, 09:54:58 PM »

Quote from: vwagon13 on August 04, 2015, 01:46:32 PM

Can't believe I am showing my nuts!

Is that the cole up on CL right now? If so that's one celebs boat and I wish my girl would let me get another closed bow fast boat. She's all about taking more people and crap with us...
I told her they want to go they can get their own boat. And try to keep up! Haha

Sent from my iPhone using SoCalJetBoats

« **Reply #36 on:** August 05, 2015, 01:55:17 PM »

Picked up these off cl. I noticed the mounting holes are a little ovaled out. Hoping they will work because i dig the rims!

Sent from my iPhone using SoCal Jet Boats

« **Reply #37 on:** August 05, 2015, 02:19:29 PM »

Uni-lug...
get the right lug nuts, has a shank and washer.

Dan'l

« **Reply #38 on:** August 05, 2015, 04:27:04 PM »

Mash is right. Seems like many old school trailer rims have that setup and the shank style lug is crucial.

Steve-O

« **Reply #39 on:** August 05, 2015, 04:42:08 PM »

Not to hijack this thread but my axles are threaded, they don't have studs. So do I need to install some 1/2-20 studs first then use the uni-lug

Sent from my iPhone using SoCal Jet Boats

« **Reply #40 on:** August 05, 2015, 06:11:07 PM »

AR rims

« **Reply #41 on:** August 05, 2015, 06:43:05 PM »

Unless they make a lug "bolt" with a shank. Seems like a possibility.

Steve-O

« **Reply #42 on:** August 05, 2015, 09:19:14 PM »

Quote from: More2LifeThanMPG on August 04, 2015, 09:54:58 PM

Is that the cole up on CL right now? If so that's one celebs boat and I wish my girl would let me get another closed bow fast boat. She's all about taking more people and crap with us...
I told her they want to go they can get their own boat. And try to keep up! Haha

Sent from my iPhone using SoCalJetBoats

im sorry....this was funny....

« **Reply #43 on:** August 05, 2015, 10:06:01 PM »

Quote from: JB1314 on August 05, 2015, 04:42:08 PM

Not to hijack this thread but my axles are threaded, they don't have studs. So do I need to install some 1/2-20 studs first then use the uni-lug

Sent from my iPhone using SoCal Jet Boats

Use some grade 8 hardened bolts from Home Depot Speed and Marine for studs, usually cap (Allen head) bolts.

And the right shanked lug nuts & washers.

Dan'l

« **Reply #44 on:** August 13, 2015, 09:23:32 AM »

I would just use threaded racing studs. Be sure to get the RIGHT washers as there are a few different types of unilug washers (offset and centered, and washer OD). Matching shank-style lug nuts are required.... make sure they aren't too long and bottom out.

« **Reply #45 on:** August 14, 2015, 05:13:16 PM »

I looked into the unilug a little and I'm not sure what I need. I know the the studs are 1/2-20 and the bolt pattern is 5x4.5. Do I just need to match those specs?

Sent from my iPhone using SoCal Jet Boats

« **Reply #46 on:** August 23, 2015, 11:53:06 AM »

Post a close up pic of the holes with the wheels off. Look on the backside for any name cast in as well.

« **Reply #47 on:** August 23, 2015, 02:17:29 PM »

I have slots on my 56... you must MIC the hole for proper size. Average mag lug shoulder thickness is around .680+. Measure the depth of hole for depth of lug shoulder. Average depth is around .500+. Factor in the supplied centered/offset washer depending if you have uni's or true bolt pattern. Call summit with those specs an make them get a set an MIC them before sending. I bought a set from them advertised .687 an they came in at .682. I called an it got taken care of fast.

« **Reply #48 on:** August 23, 2015, 08:17:35 PM »

Centerlines

Sent from my VK410 using Tapatalk

el mojado

Mrblueeyesnick

Swole Monkey

Double A

willowvalley

Undersoul02

vwagon13

jimpen

vwagon13

Steve-O

More2LifeThanMPG

JB1314

mash on it

Steve-O

JB1314

SomeThingWilder

Steve-O

JARVIS

mash on it

roost

JB1314

roost

Your Mom

tpltrbl303