SoCal Jet Boats
Discussion => The No Wake Zone => Topic started by: bkplesh on February 17, 2007, 11:22:31 AM
-
looking to buy one of these.
-
They are 20 foot openbows. (Silhouette)or Cannon boat
-
another picture
-
Thats a badass lookin' boat....nothin' handles like a cat!
-
Not bad. I have two, one twin outboard and one jet that I sold for the outboard. Now I'm thinking of going back to a jet.
-
the twin
-
better picture of the twin
-
That my friend is a bad muffucca! What speeds ya' gettin'?
[attachimg=#]
-
;;
-
You ain't gonna find a jet as fast as that widow maker! >:D[attachimg=#]
-
the picture above was 95mph with 22p props. I only get 108mph with them. Need to go better. picture of old jet
-
the jet had a 502 and went 72mph. Than I put in a blown 454 with 1000hp and with 98mph Sold the boat lees motor. Now the motor is around 1500hp on race gas
-
fun
-
more
-
Nice gearbox...
-
the twin, I built it as a demo boat so I could get a deal. The boat has only 60 hours on it. The motors are around 300hp
-
Gearbox is a 04. I have to many toy. ;D the twin needs to go. so I can finish the jet and long travel buggy. ;D
-
How big of a roost does that twin throw?
My friend's naturally aspirated jet has been clocked at 118 mph.
And to answer your subject title of "are these boats any good?", dollar for dollar, no they aren't any good. They don't throw a roost, they can't run in shallow (less than a foot) river water, they cost a mininum of $3,000 every time they go to the shop, they cost a fortune to buy, and they're difficult to work on. Other than those ugly things hanging off of the back, they're good looking boats.
-
the twin throw a big roost than my old jet did. And the jet nozzle was cut for more roost. The different between your buddy jet and my twin is, I can run all today at 100. Shallow water, The can run in 6 inch of water,the motors are set behide the tunnel.(on plane) Yes my jet run in shallow water. But stay on the gas and don't stop. My buddy thought that my twin was slow, because his when 128. Then we raced (dead stop) no bull running. He lost. But I'm going to go back to a jet. Just because I can't ski behide my twin. I try, but it sucked. The price on the twin new was 39k and my old jet or my new jet (same hull) is old with 502, (33k). New one with the blown 454, (42k)
-
The twin should run around 120 with better props. But not with me in it. 100 is to fast for me now. I've been 146 in my old hydro. I also threw out of it at 105 (bye bye boat) Plus I have a kid and want to have fun with he!!!
-
There's a lot of info in there... how do outboards throw a rooster tail? How can a prop run in shallow water?
Some friends just showed up, I gotta go.
-
IF you set the trim tabs all the way down and jack the motor all the way up and then trim the motors, while running surface props. equal big roost. first time I did that almost hit my buddy boat with water.
The water is force down the tunnel and with the motor sitting behind the tunnel openings. It makes the water seem deeper. Also with the low water pick ups on the motors, jack plate and a set back plate. Only a few inches are hanging down under the boat. I've built a few duck boats that would run on inches of water and take off in less than 16 inches of water.(with a tunnel hull design) I don't like run in shallow water. But I was racing a jet and find out the hard way, that way that the boat can run in shallow water. Looking at a sandbar and just seeing one corner with a ripple of water over the sand. trimmed up and gassed it. Made it, no mud in the roost and no dragging. I run the lowwer river. And there some sandbar!
-
That my friend is a bad muffucca! What speeds ya' gettin'?
(Attachment Link)
That's a insane looking boat with the big twins! I just sent my 21 Warlock off to get painted. Been looking for somtime of paint scheme ideas
-
IF you set the trim tabs all the way down and jack the motor all the way up and then trim the motors, while running surface props. equal big roost. first time I did that almost hit my buddy boat with water.
The water is force down the tunnel and with the motor sitting behind the tunnel openings. It makes the water seem deeper. Also with the low water pick ups on the motors, jack plate and a set back plate. Only a few inches are hanging down under the boat. I've built a few duck boats that would run on inches of water and take off in less than 16 inches of water.(with a tunnel hull design) I don't like run in shallow water. But I was racing a jet and find out the hard way, that way that the boat can run in shallow water. Looking at a sandbar and just seeing one corner with a ripple of water over the sand. trimmed up and gassed it. Made it, no mud in the roost and no dragging. I run the lowwer river. And there some sandbar!
I never wud hav thunk it possible... ::)
I found out a few minutes ago my friend's jet was 118 mph in the 1/8th mile drag, not top speed. :o . Boat is called Hellfire and ran out at Martinez/fishers landing.
-
there are some run jets that run there. like rubber ducky and moneysucker. That's were we go. I haven't been in a year and only go a few times a year. That's why the twin is going. I'm going to get a fishing boat for me and the kid. OH and fix my jet boat.
-
can you race that thing in a circle ;D
-
yes, a realy big circle!!! :o ;D
-
How big of a roost does that twin throw?
My friend's naturally aspirated jet has been clocked at 118 mph.
And to answer your subject title of "are these boats any good?", dollar for dollar, no they aren't any good. They don't throw a roost, they can't run in shallow (less than a foot) river water, they cost a mininum of $3,000 every time they go to the shop, they cost a fortune to buy, and they're difficult to work on. Other than those ugly things hanging off of the back, they're good looking boats.
I'm gonna try and keep my mouth shut on this one.....OK..I tried...where do you get this mininum of 3K every time it goes in the shop? You can rebuild the whole motor for that...But then again I guess thats the only time one is in the shop is when the motor is worn out...difficult to work on? Thats why I have one 'cause the only thing I wanna work on at the lake is my buzz...The roost and low water has already been addressed....As far as cost goes...There is that old saying...Ya' get what ya' pay for... ;)
-
more picture that I found