Null


Pages: [1]

The Chaz

  • Karma: +5/-0
Amp instalation question
« on: January 16, 2008, 07:08:15 PM »
Can anyone tell me how to hook up my amp to my deck/speakers?

I have 2 6x9 Blaupunkts hooked up to the front right and left channels so far.  They are rated at 80RMS and 240 peak

I want to hook up 2 of these also  Alpine Type R10

I need to know if the "bridge" wire is installed correctly... it came differently but wouldn't play directly from the deck until I changed it to this configuration

I will be using this to power them



It is an Audiofonics ADF-242

My deck has RCA? jacks on the back for the rear channel and the amp has RCA? inputs for channel 1/2 and 3/4

Please help
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

hotrod56cars

  • Karma: +1/-8
Re: Amp instalation question
« Reply #1 on: January 16, 2008, 07:54:19 PM »
I can, as well as several others on here.   ;)  619-787-7987

I don't understand if your amp is already in your vehicle powering the  6 X 9 Blaupunkts or if they are in there powered by the stereo?   ???

The woofer in the picture is wired correctly if it's the only woofer in the system and is going to be powered by a mono/bridged signal.

I don't know anything about your Audiofonics ADF-242, I don't know if it's bridgeable ( I am assuming it is otherwise you wouldn't have it), load/impedence requirements, nothing...  ???

If you want my help call me... I think you have a beer credit at the moment...  :D

Power the 6 X 9's with 1 & 2 and bridge 3 & 4 for the sub, probably............
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party
Quote
NO REGRET$ ... Arguing on the internet is like competing in the Special Olympics / no matter how good you do you're still retarded!!!!!

                                                          1978  19' Mach 1 Tunnel jet

Jetaholic

  • Karma: +3/-0
Re: Amp instalation question
« Reply #2 on: January 16, 2008, 08:37:15 PM »
Basically the amp is a 4 channel amp. Typically 4 channel amps are used to power a Front Left, Front Right, Rear Left, Rear Right speaker setup.

However, since you're gonna be running subs and the rear outs from the deck, you'll only need to hook up channels 1 & 2 L/R. 3 and 4 would have nothing going to them.

For subs, it's best to bridge the output of 1 and 2 if it is bridgeable. If you could post a link or a copy of the owners manual that would help out immensely.
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party
To err is human, to forgive divine...except for running Fords ;D

F - Found
O - On
R - River
D - Dead

The Chaz

  • Karma: +5/-0
Re: Amp instalation question
« Reply #3 on: January 16, 2008, 09:30:12 PM »
Thanks for the reply ;D  Rod walked me through it on the phone... Thanks Rod!!!  I will install it tomorrow in the boat and let you know how it sounds O0
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party
Pages: [1]
 


Null

SMFPacks CMS 1.0.3 © 2026