What did you do to your boat today?

« **Reply #1450 on:** January 18, 2015, 07:44:01 PM »

Had b1 put a new lo pro in the SWTD and some other things. Intake went in at 5.4 and the shoe looks great. We sent her back about 2 and a half inches. She is sticking out a little farther than normal. 😁😁😁

Sent from my iPhone using SoCalJetBoats mobile app

« **Reply #1451 on:** January 18, 2015, 08:03:00 PM »

Looking good Jake

« **Reply #1452 on:** January 18, 2015, 08:44:59 PM »

Quote from: BOOST on January 18, 2015, 08:03:00 PM

Looking good Jake

Thanks bud. Excited to see what it will do.

Sent from my iPhone using SoCalJetBoats mobile app

« **Reply #1453 on:** January 18, 2015, 08:48:41 PM »

Like wise little more hole shot ?

« **Reply #1454 on:** January 18, 2015, 08:57:14 PM »

waiting for the motor so took the time to strip her down to nothing. from rub rail, to tossing nasty carpet and running the orbital all over with boat candy...... passing time with tasks that NEED to be done...

granted - would not be doing ANY of this if the motor was ready to go

« **Reply #1455 on:** January 18, 2015, 09:41:17 PM »

Quote from: BOOST on January 18, 2015, 08:48:41 PM

Like wise little more hole shot ?

Chris and I are hoping it will free it up a bit more. It was more his idea than mine to do the set back, iam excited to see what it does. Along with more power and the edelbrock fogger

Sent from my iPhone using SoCalJetBoats mobile app

« **Reply #1456 on:** January 18, 2015, 09:42:51 PM »

Very nice Jake

« **Reply #1457 on:** January 19, 2015, 12:28:08 AM »

Pulled the 4150 intake and set the tram on it to see what it looks like before I pull the motor tomorrow..

Sent from my MB860 using SoCal Jet Boats mobile app

« **Reply #1458 on:** January 19, 2015, 12:33:19 AM »

All I did was look at mine trying to figure out why January has to be so cold

« **Reply #1459 on:** January 19, 2015, 01:02:42 AM »

Eat shit friend!!!>

Sent from my MB860 using SoCal Jet Boats mobile app

« **Reply #1460 on:** January 19, 2015, 04:43:41 AM »

Quote from: jyeager on January 18, 2015, 09:41:17 PM

Chris and I are hoping it will free it up a bit more. It was more his idea than mine to do the set back, iam excited to see what it does. Along with more power and the edelbrock fogger

Sent from my iPhone using SoCalJetBoats mobile app

looks bad ass jake! Should be doing the same thing in a couple weeks.

"RTCP"

« **Reply #1461 on:** January 19, 2015, 12:33:24 PM »

Finally set the intake on cruiser this weekend and checked the alignment on the TA plate. Also prepped for the trailer dismount to begin the bottom work, two engine hoists handle this thing pretty good.

« **Reply #1462 on:** January 19, 2015, 03:47:52 PM »

Just picked up the seats from the upholstery guy 👍

Sent from my iPhone using SoCal Jet Boats

« **Reply #1463 on:** January 20, 2015, 03:46:47 PM »

Quote from: jamiemwedmore1234 on January 18, 2015, 11:33:43 AM

Pulled the pump got a (A) Bronze impeller and a stuffer already in the bowl need to upgrade the shaft new bearing and a inducer and prolly wear ring off to b-1 racing I go

Sent from my iPad using SoCal Jet Boats

found out I have a (C) cutt impeller and a twisted shaft and bad bearing. So now I get a aq shaft new inducer new bearing and wear ring should run like a raped ape

Sent from my iPad using SoCal Jet Boats

« **Reply #1464 on:** January 20, 2015, 03:47:18 PM »

Quote from: jamiemwedmore1234 on January 18, 2015, 11:33:43 AM

Pulled the pump got a (A) Bronze impeller and a stuffer already in the bowl need to upgrade the shaft new bearing and a inducer and prolly wear ring off to b-1 racing I go

Sent from my iPad using SoCal Jet Boats

found out I have a (C) cutt impeller and a twisted shaft and bad bearing. So now I get a aq shaft new inducer new bearing and wear ring should run like a raped ape

Sent from my iPad using SoCal Jet Boats

« **Reply #1465 on:** January 20, 2015, 03:47:56 PM »

Quote from: jamiemwedmore1234 on January 18, 2015, 11:33:43 AM

Pulled the pump got a (A) Bronze impeller and a stuffer already in the bowl need to upgrade the shaft new bearing and a inducer and prolly wear ring off to b-1 racing I go

Sent from my iPad using SoCal Jet Boats

found out I have a (C) cutt impeller and a twisted shaft and bad bearing. So now I get a aq shaft new inducer new bearing and wear ring should run like a raped ape

Sent from my iPad using SoCal Jet Boats

« **Reply #1466 on:** January 21, 2015, 12:41:52 AM »

Got the motor out..just gotta start shittin sum cnotes to get the changes made fast>

Sent from my MB860 using SoCal Jet Boats mobile app

« **Reply #1467 on:** January 21, 2015, 01:12:10 AM »

I took the pink cf numbers off my boat and replaced them with blue numbers

« **Reply #1468 on:** January 21, 2015, 01:15:00 AM »

Nice!!!

Sent from my MB860 using SoCal Jet Boats mobile app

« **Reply #1469 on:** January 21, 2015, 12:24:27 PM »

Today I registered my boat and trailer so if anything happens I don't have to jump through hoops

« **Reply #1470 on:** January 21, 2015, 07:24:09 PM »

Began pulling it apart

« **Reply #1471 on:** January 21, 2015, 07:25:03 PM »

Anyone know what I'm workin with

« **Reply #1472 on:** January 21, 2015, 07:28:31 PM »

Be sure to bag and Mark your parts from where they came from. I'm not a ache b

A Cheby guy so can't help you there.

Sent from my iPhone using SoCal Jet Boats

« **Reply #1473 on:** January 21, 2015, 07:51:20 PM »

Looks like a pair of early 70's oval port heads with some crane roller rockerz and jomar style stud girdles to me... hope that helps... have funO0

Sent from my MB860 using SoCal Jet Boats mobile app

« **Reply #1474 on:** January 21, 2015, 08:09:41 PM »

Good?

?

jyeager

BOOST

jyeager

BOOST

socaljst1970

jyeager

BOOST

aquaholic72

matches909

aquaholic72

capogniracing

HaulsBalls

K-034

jamiemwedmore1234

jamiemwedmore1234

jamiemwedmore1234

aquaholic72

matches909

aquaholic72

matches909

Tylertjeep73

Tylertjeep73

angermgmt

aquaholic72

Tylertjeep73