SoCal Jet Boats

Discussion => Topock / Laughlin => Topic started by: Maker on August 14, 2014, 09:13:16 PM

Title: 8/17 Laughlin Bullhead
Post by: Maker on August 14, 2014, 09:13:16 PM
 If all goes well and I'm not working  we will be putting the new to us boat in the water 

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: TrollerDave on August 14, 2014, 10:10:06 PM
What did you end up getting?
Title: Re: 8/17 Laughlin Bullhead
Post by: rush1 on August 14, 2014, 10:26:07 PM
Rdp is having the dam to dam run on Lake Mojave this weekend

Sent from my SM-P600 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 15, 2014, 04:11:55 AM
I ended up getting a Rogers bubbled eck  18ft open bow

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: beerjet on August 15, 2014, 06:53:38 AM
Rdp is having the dam to dam run on Lake Mojave this weekend

Sent from my SM-P600 using SoCal Jet Boats mobile app
Who?

-beerjet-

Title: Re: 8/17 Laughlin Bullhead
Post by: rush1 on August 15, 2014, 06:54:56 AM
I know I should of said take it to the scjb event.

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 15, 2014, 11:34:52 AM
I would like to go to this event  too bad I'm on call Saturday

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 16, 2014, 03:44:27 PM
I'll be on the water around 11am sunday

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 17, 2014, 04:55:56 PM
Well the day started out good until  one of the carbs started to leak  I'm not sure yet if it's a stuck float or the needle and seat  but I'll find  out when I get her home

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 17, 2014, 07:43:48 PM
So do I need a wedge or what the roost is weak 

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 17, 2014, 08:49:04 PM
I wish I was able to take a picture  but I was too busy shaking her down   
From what I was able to see the roost was only about 4ft the pic is all the way up
Title: Re: 8/17 Laughlin Bullhead
Post by: daniel.sykes on August 18, 2014, 03:55:48 PM
I would try to adjust your cable a little bit more unless the diverted is topped then a wedge is good but remember that if you have any porpoising issues then they get worst if you add a wedge

Sent from my XT907 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 18, 2014, 04:09:38 PM
Ok thanks ill have to give that a try after I rebuild my carbs    didn't notice any porpoising  but I wasn't out very long   I'm going to try and get back on the water this weekend

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 22, 2014, 04:13:31 PM
I would try to adjust your cable a little bit more unless the diverted is topped then a wedge is good but remember that if you have any porpoising issues then they get worst if you add a wedge

I was able to adjust the cable a bit more  it's a little better  so I guess the next step is a wedge

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: daniel.sykes on August 28, 2014, 09:09:00 AM
This is the angle I have on mine with a wedge

Sent from my XT907 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: Maker on August 28, 2014, 09:32:11 AM
What degree wedge did you use

Sent from my SCH-I545 using SoCal Jet Boats mobile app

Title: Re: 8/17 Laughlin Bullhead
Post by: daniel.sykes on September 01, 2014, 10:54:25 AM
I don't know I had it around soon I put it on but it is 1\4 inch on top and 11\16 of an inch on the bottom

Sent from my XT907 using SoCal Jet Boats mobile app

SMFPacks CMS 1.0.3 © 2026