SoCal Jet Boats
Classifieds => WTB => Topic started by: Bunger on May 26, 2015, 04:56:13 AM
-
Need to get the oil temps
Down looking for a smaller cooler. I know there's different styles and im not even quite sure what I want to go with. Those Olson style setups look pretty trick with the oil filter on them. Also I guess I need some sort of oil filter relocation kit. It's going on a 455.
Sent from my iPhone using SoCalJetBoats
-
I have an inline oil cooler, about 10" long. Used on Mercruiser for cooling p/s fluid. I also have an oil relocator setup with all the hoses.
100 shipped.
Contact me if you want it
Sent from my iPhone using SoCal Jet Boats
-
Removed..
-
If bunger doesn't take you up I might be interested. Do you have some pics of the setup?
-
Yes I would like to see some pics also. Are the oil and water inlets threaded? And the oil filter setup will work on a bbo?
Sent from my iPhone using SoCalJetBoats
-
Yes I would like to see some pics also. Are the oil and water inlets threaded? And the oil filter setup will work on a bbo?
Sent from my iPhone using SoCalJetBoats
Here are some pics...
Water lines are not threaded, oil lines are...
Oil filter set up has one side that threads to factory housing, the other side can be mounted anywhere with the filter.
Sent from my iPhone using SoCal Jet Boats
-
Interested if the other 2 guys pass
-
I also have a rare nicson oil filter relocator...brings the filter out from under the engine to in front of the bell housing
I have many of the remote oil filter set ups for those interested, although I only have one oil cooler.
Sent from my iPhone using SoCal Jet Boats
-
What could be causing my oil to get so hot? Maybe I have more problems than needing a oil cooler. It got as hot as 280-290 last weekend. I could keep it at 260-270 if I stuck around 3000-3500 rpm and once I idle,for a few min down to 190. Doesn't seem to be lean. The two middle cylinders look leaner according to the plugs. 12 qrt pan vr1straight 50
Sent from my iPad using SoCalJetBoats
-
Are you sure the gauge is correct? That's cooking the $#!+ out of the oil.
-
Does the engine turn easily by hand?
-
Does the engine turn easily by hand?
Ya it does had the motor out over winter everything looked good. And ya gauge should be correct its a brand new auto meter and autometer sender. And it's in a bung i welded in the bottom of the oil pan. Water temp is a tad over 120 while cruising and will bump up to 140 while idling until the oil cools down. Runs awesome aside from the oil temp
Sent from my iPhone using SoCalJetBoats
-
Are u. Running over transom ?
If you are have a bung welded on feach header put a hose from your breathers to the bungs it should help cool oil down did it on my buddy it worked
Sent from my iPhone using SoCal Jet Boats
-
Are u. Running over transom ?
If you are have a bung welded on feach header put a hose from your breathers to the bungs it should help cool oil down did it on my buddy it worked
Sent from my iPhone using SoCal Jet Boats
W T F are you taking about?
Evac tubes off the headers to cool oil temps!?
Would have been better advice to throw a few ice cubes in the crank case before each run 😜🙊
Sent from my iPhone using SoCal Jet Boats
-
You don't know as much as you think you do once again you are chiming to run your mouth we did this on a 455 already worked so take it for what it worth
Sent from my iPhone using SoCal Jet Boats
-
If u were as good with olds u would be world famous like the mondellos but your not so get off your high horse
Sent from my iPhone using SoCal Jet Boats
-
You don't know as much as you think you do once again you are chiming to run your mouth we did this on a 455 already worked so take it for what it worth
Sent from my iPhone using SoCal Jet Boats
You've been advised to take a grammar and punctuation class... You obviously didn't...
Funny how I don't know as much as you, but I run a successful business and am ASE master tech certified... Not your hillbilly trial and error
Bunger knows what he wants and good from bad.... I'm sure he knows the value of your advice
Sent from my iPhone using SoCal Jet Boats
-
That all it is advise not a pissing match I pretty sure you know what you are doing also you not here to step on any 1 toes what . What I suggest is advise we have Tryed it and it worked so but oil cooler is the best way to go not trying to hurt your sale just offering advise.
Sent from my iPhone using SoCal Jet Boats
-
Ya im not seeing how increasing crank case vaccum will lower oil temps???
I 99% sure the solution to my
Problem is a small heat exchanger plumbed to the dump line. Should be enough to drop oil temp to where I want it
Sent from my iPhone using SoCalJetBoats
-
That all it is advise not a pissing match I pretty sure you know what you are doing also you not here to step on any 1 toes what . What I suggest is advise we have Tryed it and it worked so but oil cooler is the best way to go not trying to hurt your sale just offering advise.
Sent from my iPhone using SoCal Jet Boats
When you offer up advise, it has to be worthwhile...
If someone wants a faster boat, you dont offer advise like buy a better trailer.
You arnt hurting my sale, as you clearly indicate the the right way to cool oil temps is with an exchanger, not your initial evac deal
Sent from my iPhone using SoCal Jet Boats
-
Ok sound like u got it
Sent from my iPhone using SoCal Jet Boats
-
No I said it help drop temp on our olds the only way is oil cooler. were not reinventing the wheel sound like he know what he want so good luck
Sent from my iPhone using SoCal Jet Boats
-
I'm not trying to stir the pot and I know I am going to take a beating over this, but...
A. I think your water temp is too high.
B. Installing a heat exchanger on the dump line will add a restriction and therefore increase block pressure.
I think much too much value is being placed on water temp and not on actual block temp or oil temp.
-
I'm not trying to stir the pot and I know I am going to take a beating over this, but...
A. I think your water temp is too high.
B. Installing a heat exchanger on the dump line will add a restriction and therefore increase block pressure.
I think much too much value is being placed on water temp and not on actual block temp or oil temp.
I've never seen my water temp over 140. 140 is idling after a good long cruise and the water soaking the heat out of the oil and block. After a few minutes it's back to 120.
The block pressure did go through my head but I feel like the water from the pump will cool the oil too much and take longer to get the oil warm
Sent from my iPhone using SoCalJetBoats
-
My theory is, what is the velocity of the water and how much heat energy is required to raise the temperature to 140 degrees F?
It's a lot of water so it must be a lot of energy.
-
I think you have too much oil in the pan. .... foam don't cool.
Just my humble opinion.
GT
-
I think you have too much oil in the pan. .... foam don't cool.
Just my humble opinion.
GT
Hmm that's possible. It shows a qrt and a half high when it's cold but warm it's right at the line maybe a bit over. I'll try draining
Sent from my iPhone using SoCalJetBoats
-
Maybe it's a 10qrt not a 12 like i thot
Sent from my iPhone using SoCalJetBoats
-
Maybe it's a 10qrt not a 12 like i thot
Sent from my iPhone using SoCalJetBoats
A 10 quart pan don't hold ten quarts and a twelve quart pan would be unusual.
GT
-
Back when I had an olds... I ran it at 160/180 to avoid water pressure cracking the heads around valves( Ga/B big valve heads). You want to keep a stock oil pump an drill out the returns in the heads. Use good oil like Vr1 with napa gold or wix filter an about 1qt less than pan states. This is what I did with mine for mostly stock an mild cam.
-
Back when I had an olds... I ran it at 160/180 to avoid water pressure cracking the heads around valves( Ga/B big valve heads). You want to keep a stock oil pump an drill out the returns in the heads. Use good oil like Vr1 with napa gold or wix filter an about 1qt less than pan states. This is what I did with mine for mostly stock an mild cam.
I had a pressure gauge on the intake and set my gate and relief valve and got no more than 14psi at wot. So I'm not worried about that. I did external return lines to the pan so I'm not worried about that either. Run vr1 sae 50.
Sent from my iPad using SoCalJetBoats
-
But I have been running 12 quarts since I got the boat so I'll drop to 10 or so and see if that helps my problem. Could a lean situation make the oil get that hot? And run for 3 summer that lean without having problems lol
Sent from my iPad using SoCalJetBoats
-
My olds runs no more than 140 , no matter what I'm doing. Also I have a Dooley pan that is a 10 qt . And I put 9 qt in it. Just thought I'd give my 2 cents!!😀
Sent from my iPhone using SoCalJetBoats
-
My olds runs no more than 140 , no matter what I'm doing. Also I have a Dooley pan that is a 10 qt . And I put 9 qt in it. Just thought I'd give my 2 cents!!😀
Sent from my iPhone using SoCalJetBoats
Ya mine never goes over 140. U don't happen to have a pic of your pan do you? Been trying to figure out what mine is haha.
Sent from my iPad using SoCalJetBoats
-
Yah I can take one for you. Pm me and I will send you a few.
Sent from my iPhone using SoCalJetBoats