My first jet. 69 schiada

« **Reply #300 on:** March 31, 2011, 10:28:18 PM »

Made a flywheel cover today

Weld porn

« **Reply #301 on:** April 06, 2011, 06:15:46 PM »

got the motor in for the final time today. plumbing,wiring, gauges, and little details is pretty much all I have left.

« **Reply #302 on:** April 06, 2011, 06:52:00 PM »

Looking good

One question tho, you have enough of the input shaft of the pump in the output of the motor

Lotta spline showing

« **Reply #303 on:** April 06, 2011, 06:55:57 PM »

its a long shaft pump. i only have 1/8"- 3/16" slop till it bottoms out

« **Reply #304 on:** April 06, 2011, 07:12:05 PM »

Cool

Just noticed alot of spline so was curious

Nice work

« **Reply #305 on:** April 06, 2011, 07:15:36 PM »

that bellhousing cover turned out badass. seriously that thing is sweet.

« **Reply #306 on:** April 06, 2011, 08:12:17 PM »

man that thing sounds pissed off! way to go!!!!!!

« **Reply #307 on:** April 06, 2011, 10:44:19 PM »

Thanks guys, almost done with this shit

« **Reply #308 on:** April 08, 2011, 08:58:18 PM »

Plumbed it and slid in new gauges

« **Reply #309 on:** April 08, 2011, 09:50:35 PM »

Only one word for it man............WOW!!!!

Wonderful work!

Ray

« **Reply #310 on:** April 09, 2011, 09:10:05 AM »

Quote from: 76NORDIC on April 06, 2011, 07:12:05 PM

Cool Just noticed alot of spline so was curious Nice work

Hey Kev....what seals the front of the bearing? Most I've seen seal around the OD of the driveline yoke

« **Reply #311 on:** April 09, 2011, 09:20:12 AM »

its a thin cap. its not a thick one that looks like a pulley, know what i mean?
pic from last year

« **Reply #312 on:** April 09, 2011, 09:23:43 AM »

so I am trying to research on tuning this thing. taking the laptop over today to set the timing.
I also need to figure out what I'm gonna do for header lines.
Pat shoot me a pic of a tape measure on your bbc head exhaust ports i think its close enough that i can just modify a set of bbc header lines.

« **Reply #313 on:** April 09, 2011, 09:32:43 AM »

Quote from: sandeggo on April 06, 2011, 06:15:46 PM

got the motor in for the final time today. plumbing,wiring, gauges, and little details is pretty much all I have left.

Saw the rails at the shop after they were water jetted. Looked cool then and now that there polished WOW.

« **Reply #314 on:** April 09, 2011, 09:44:48 AM »

yeah everything is a half ass polish though. it will have to wait till next season to get the real deal. I can live with pits and scratches for this season.

« **Reply #315 on:** April 09, 2011, 09:45:39 AM »

Quote from: sandeggo on April 09, 2011, 09:23:43 AM

so I am trying to research on tuning this thing. taking the laptop over today to set the timing.
I also need to figure out what I'm gonna do for header lines.
Pat shoot me a pic of a tape measure on your bbc head exhaust ports i think its close enough that i can just modify a set of bbc header lines.

I've got you covered on the lines. Give me a call

« **Reply #316 on:** April 10, 2011, 07:10:07 PM »

Did some trailer work today, I'll be Very happy to shitcan the floater bar. Added a winch and V-Bunks up under the boat

« **Reply #317 on:** April 11, 2011, 06:18:32 PM »

I just sat in total amazement as I read the whole thread from start to finish...What a great journey and the workmanship that you displayed and the entire evolution of your project is something that I hope that you are very proud of .

I can't thank you enought for sharing and to the people that helped you along the way with parts, advice and material way to go guys!!!!!

« **Reply #318 on:** April 12, 2011, 03:13:16 PM »

thanks! kind words.
today I decided I didn't have $100 bucks for transom block offs. made some out of 304 S.S.

« **Reply #319 on:** April 12, 2011, 03:19:07 PM »

Inner and outer ring

Last thing I gotta make is my header lines. Got that figured out already just gotta do it

« **Reply #320 on:** April 18, 2011, 12:34:19 PM »

A lil chrome never hurt nobody

« **Reply #321 on:** April 18, 2011, 05:57:55 PM »

Quote from: sandeggo on April 18, 2011, 12:34:19 PM

A lil chrome never hurt nobody

OOOOO looks nice

« **Reply #322 on:** April 19, 2011, 10:00:58 PM »

Got mynew rack in the mail today. Also made some waterlines.
.5" .035" wall stainless tube, and 1/4" .035" wall tube. Total cost to make these water lines will be 45$. Sorry Bassett but 175$ is way too much for waterlines.

« **Reply #323 on:** April 20, 2011, 03:53:35 PM »

Before someone else says it SHOW US YOUR RACK!!!!!!

Scoop looks great.

« **Reply #324 on:** April 24, 2011, 07:13:43 AM »

Well first day on the water went great!!! It runs faster than before. It's alot more fun now and is way torqueier.
I gotta play with the tuning and rideplate getting it dialed in.

sandeggo

sandeggo

76NORDIC

sandeggo

76NORDIC

Nixonnow

Nordie

sandeggo

sandeggo

IRRebel

lbhsbz

sandeggo

sandeggo

76 Bonneville

sandeggo

lbhsbz

sandeggo

logans runner

sandeggo

sandeggo

sandeggo

SuperJet

sandeggo

logans runner

sandeggo