TX 19 youngblood

« **Reply #125 on:** February 14, 2010, 12:45:00 PM »

I made a boxed tray for the hydraulic pump ditch the old lines from the pump and went with stainless braided lines, finished up running the nylon wire loom to the transom getting closer

« **Reply #126 on:** February 14, 2010, 01:10:20 PM »

Hell ya looks clean!

« **Reply #127 on:** February 14, 2010, 02:05:04 PM »

Looking good Brian!

« **Reply #128 on:** March 07, 2010, 02:29:06 PM »

I got Nick hard at work he made me up a bracket for my fuel block

All I need now is 8 -6 120 degree double swivel from the fuel block to the float bowls. at $21.47 each

« **Reply #129 on:** March 07, 2010, 05:22:42 PM »

Quote from: boost on March 07, 2010, 02:29:06 PM

I got Nick hard at work he made me up a bracket for my fuel block All I need now is 8 -6 120 degree double swivel from the fuel block to the float bowls. at $21.47 each

nick always does great work

dont start bitchin about money now foooo

looks good, where u been

« **Reply #130 on:** March 07, 2010, 05:37:34 PM »

Quote from: Ralph Brunt on March 07, 2010, 05:22:42 PM

nick always does great work

dont start bitchin about money now foooo

looks good, where u been

Thanks Ralph I've been real busy lately trying to finish up the boat

« **Reply #131 on:** March 07, 2010, 08:47:50 PM »

So Brian, everything looks tits!!! You gonna keep this one? lol

« **Reply #132 on:** March 07, 2010, 09:59:39 PM »

Quote from: v-drive video on March 07, 2010, 08:47:50 PM

So Brian, everything looks tits!!! You gonna keep this one? lol

Thanks jerry yep its a keeper.

« **Reply #133 on:** March 07, 2010, 10:07:49 PM »

I should think so! I can't see where you could improve with anything else anyway

So why bother?

THIS is gonna be fun to see this run!

Ray

« **Reply #134 on:** March 08, 2010, 06:58:21 PM »

I can't see where you could improve with anything else anyway So why bother?

19' tunnel would be nice.

« **Reply #135 on:** March 08, 2010, 07:00:58 PM »

Quote from: bertus on January 21, 2010, 10:12:26 PM

Damn Brian the new diggs are lookin bad a$$. That thing is gonna be one bad mofo .

Thanks bro

« **Reply #136 on:** March 12, 2010, 06:02:23 PM »

I had the scoop coated gloss black and headers ceramic coated black.Nick came through once again on making the scoop

almost ready going to have to redo my rail setup before the motor goes in

« **Reply #137 on:** March 12, 2010, 06:04:52 PM »

i sure hope it hauls the mail, cause it looks fockin fast

« **Reply #138 on:** March 12, 2010, 06:21:45 PM »

Everything turned out SICK!

« **Reply #139 on:** March 12, 2010, 07:02:46 PM »

Quote from: boost on March 12, 2010, 06:02:23 PM

All my hard work payed off had the scoop coated gloss black and headers ceramic coated in black.Nick came through once again on making the scoop he didn't even tell me he was making it for me until it was done almost ready going to have to redo my rail setup before the motor goes in

brian looks good

« **Reply #140 on:** March 12, 2010, 07:07:56 PM »

Looking good Brian, looking good.

« **Reply #141 on:** March 12, 2010, 08:10:10 PM »

Hell yeah Brian looking bada$$

« **Reply #142 on:** March 14, 2010, 09:09:48 AM »

Had to make some new outside rails the original one in the picture on the left was only 1''x 1/4 x3' and it bowed in the middle when tightened down so i went with 6061 aluminum and made it 2'' .

« **Reply #143 on:** March 14, 2010, 11:52:34 AM »

Those turned out nice! you do good work!

« **Reply #144 on:** March 14, 2010, 12:02:02 PM »

Quote from: cj222 on March 14, 2010, 11:52:34 AM

Those turned out nice! you do good work!

Thanks bud for making them for me just got me thinking who building the boat sh't bro your all in

thanks for the motivation when things don't fit are don't work out your pushing to get it done. Hope I can be some useful help on yours.

« **Reply #145 on:** March 14, 2010, 12:04:08 PM »

Glad to help out! I like to make and build shit

« **Reply #146 on:** March 27, 2010, 08:45:56 PM »

After I had to have new rails made and waiting to get them back from powder coating finally got them install this weekend, along with the motor.

« **Reply #147 on:** March 27, 2010, 08:48:58 PM »

Lookin good Brian. Good to see you guys today.

« **Reply #148 on:** March 28, 2010, 10:26:20 AM »

Quote from: flytime on March 27, 2010, 08:48:58 PM

Lookin good Brian. Good to see you guys today.

Thanks Bob for you and Ron hanging out with us.

« **Reply #149 on:** March 28, 2010, 10:32:47 AM »

MADSKILLZ came up with this trick out throttle bracket work out great

BOOST

MADSKILLZ

Luckie Stiff

BOOST

Ralph Brunt

BOOST

v-drive video

BOOST

IRRebel

BOOST

BOOST

BOOST

Ralph Brunt

MADSKILLZ

challenger

Luckie Stiff

bertus

BOOST

MADSKILLZ

BOOST

MADSKILLZ

BOOST

flytime

BOOST

BOOST