Stud girdles( girdle or not to girldle)

« **on:** July 04, 2013, 08:29:03 AM »

So a quick question who runs girdles and who doesn't and what are ur guys thoughts pros cons

Sent from my HTC Sensation 4G using SoCalJetBoats mobile app

« **Reply #1 on:** July 04, 2013, 08:39:56 AM »

for the heads??? or the bottom end???

« **Reply #2 on:** July 04, 2013, 08:43:55 AM »

Heads

Sent from my HTC Sensation 4G using SoCalJetBoats mobile app

« **Reply #3 on:** July 04, 2013, 08:46:20 AM »

Sent from my HTC Sensation 4G using SoCalJetBoats mobile app

« **Reply #4 on:** July 04, 2013, 09:03:37 AM »

Depends on how big your cam is but IMO! I would run them it's a Lil xtra insurance for your studs...

😎

« **Reply #5 on:** July 04, 2013, 09:05:02 AM »

If you decide to not run them I'll buy em from ya! I need another set...

😎

« **Reply #6 on:** July 04, 2013, 09:13:18 AM »

That depends, on cam size your springs and the heads! what are you running?

« **Reply #7 on:** July 04, 2013, 09:24:45 AM »

Well the cam has a 710 lift on it the motor was a 502 then rebuilt it to a 540 was thinking just doing Polly locks the problem I'm having is they worked great before l rebuilt the motor now well see pic below it's not keeping the studs tight and the roller rockers loosen up not good

Sent from my HTC Sensation 4G using SoCalJetBoats mobile app

« **Reply #8 on:** July 04, 2013, 09:33:04 AM »

well if it were mine and things kept loosening up id replace the studs and the locks girdles are for stretch and flex. yah you may want them also. how hard are you pushing the engine??? if you are using it hard yes most defiantly.

« **Reply #9 on:** July 04, 2013, 09:58:39 AM »

I replaced the studs ARP I was thinking just running Polly locks but have never know anyone who has ran them and I haunt ran the motor hard at all just getting it broke in

Sent from my HTC Sensation 4G using SoCalJetBoats mobile app

« **Reply #10 on:** July 04, 2013, 11:23:41 AM »

Given the lift at the valve and knowing the typical spring pressures required for such valve lift, I strongly recommend keeping the rocker stud girdle on your engine.

Loosened rocker studs and/or loosened poly locks is not the girdles fault, nor is keeping them tight the primary reason for running a girdle in the first place. Figure out what's going on there.

LO

got the squirts

Stud girdles( girdle or not to girldle)

mobboss

Re: Stud girdles( girdle or not to girldle)

got the squirts

Re: Stud girdles( girdle or not to girldle)

got the squirts

Re: Stud girdles( girdle or not to girldle)

2fass 4 you

Re: Stud girdles( girdle or not to girldle)

2fass 4 you

Re: Stud girdles( girdle or not to girldle)

mobboss

Re: Stud girdles( girdle or not to girldle)

got the squirts

Re: Stud girdles( girdle or not to girldle)

mobboss

Re: Stud girdles( girdle or not to girldle)

got the squirts

Re: Stud girdles( girdle or not to girldle)

LakesOnly

Re: Stud girdles( girdle or not to girldle)