Null

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - jim99

Pages: [1]
1
Project Boats For Sale / 70's Hondo 21' "mini daycruiser"
« on: July 25, 2015, 05:19:07 PM »
I have a 70's (not sure paperwork says 72 but I thought it was 76) Hondo 21' closed bow boat that I'm trying to sell, I'm trying to figure out the value, it runs good but hasn't been used in a few years but I fired it up today without a problem (it's been fired up routinely), Berkley jet, 454, etc.  I call it a mini daycruiser because it's a hull I've never seen before, it's closed hull and was made by Hondo, below is a picture.  It definitely needs interior work, all the vinyl is cracked badly.  Does anyone have any interest in this?  Any idea of the value?

Thanks!!

2
Boats For Sale / 70's Hondo 21" "mini daycruiser"
« on: July 25, 2015, 05:17:56 PM »
I have a 70's (not sure paperwork says 72 but I thought it was 76) Hondo 21' closed bow boat that I'm trying to sell, I'm trying to figure out the value, it runs good but hasn't been used in a few years but I fired it up today without a problem (it's been fired up routinely), Berkley jet, 454, etc.  I call it a mini daycruiser because it's a hull I've never seen before, it's closed hull and was made by Hondo, below is a picture.  It definitely needs interior work, all the vinyl is cracked badly.  Does anyone have any interest in this?  Any idea of the value?

Thanks!!

3
Jet Pumps / Lots of leakage around pump
« on: July 24, 2015, 09:40:24 PM »
Have a new/used boat, 21' ultra lx, 502, dominator jet, just purchased.

Took it out for first time today, getting a lot of water in bilge, I can see water running down from top of pump inside bilge, not gushing but a pretty good trickle.  The previous owner had ran a new bead of silicon around the entire outside of the pump, clearly he had this problem before.  I included picture but you probably can't see trickle.

Do I need to have someone (or myself) pull the pump completely to seal it properly or is there an easier way to take care of this, apparently a bead of silicon isn't taking care of it.  Any idea what the cost would be for someone to do this? 

Any ideas or recommendations would be great.

Thx for any input/suggestions.

Boat is currently in bullhead, any recommendations for service in bullhead or Mohave valley would be welcomed as well.




Sent from my iPhone using SoCal Jet Boats

4
Have a new/used boat, 21' ultra lx, 502, dominator jet, according to previous owner it had been sitting without use for a couple of years but carb had been rebuilt recently (Holley 750)

Took it out for first time today, if I give full throttle it just bogs down and almost dies and backfires, if I ease the throttle up I can get it to cruise at a max of about 4000 rpm (30-33 mph).  If I continue giving more throttle it bogs down to 3000 or less, misses and backfires.

I checked secondaries and they seem to be smooth to open, checked the accelerator pump and it squirts gas when manually operated.

I seem to hear the secondaries open and close via vacuum but not completely sure, however when I think I hear them close that's when power come back.

Any ideas??

Does 32mph at 4000rpm sound right?

Thx for any input/suggestions.




Sent from my iPhone using SoCal Jet Boats

5
Topock / Laughlin / fuel on river
« on: July 19, 2015, 02:43:48 AM »
Is there any fuel on the river north of Avi any longer?  Avi's pumps are hit and miss as well, sometimes they have fuel, sometimes they don't.  Otherwise down to Needles or ???

thanks

6
Jet Pumps / newbie help questions
« on: July 19, 2015, 02:30:19 AM »
I just purchased an Ultra 21lx with a jet I'm not familiar with, sorry for the newbie questions.  My previous jet had a cleanout in the bilge and a couple of plugs that I put gear oil into, this one is completely different and I'm not familiar with it.  Need some advice for how to clean it out (if debris gets in it) and what (if any) maintenance is needed.  I think it's a water lubricated pump maybe (don't really know).  If it is, can you run these dry for any length of time (30 sec even or??)??  Is the clean out the triangular plate with the three bolts? (seems a lot more difficult than the two wingnuts that I used to have on the other jet).  I've attached a picture, I'd love any suggestions, recommendations, help, etc...............

thanks


7
Engine Mechanical / Electrical / OC IE repair work
« on: July 19, 2015, 02:14:14 AM »
Looking for general repair/maintenance work for 21lx ultra with berkley pump.  Any recommendations out there?

Pages: [1]

Null

SMFPacks CMS 1.0.3 © 2026