set of tabs

« **on:** February 03, 2013, 09:47:06 AM »

Guys . i got a product im looking for . They are called "Step-N-Trim Tabs" Got a porposing problem . Mild . Got a 20' ultra custom open bow w a 454/ dominator and droop snoot . and a ride plate as well . Got a buddy who runs a set and they we're like the magic needed to smooth out his ride . problem is....I cant find any ! Help !!! Found one on ebay . but i need two . Hit me up if ya got a pair of them you dont need . 817-845-2887

« **Reply #1 on:** February 03, 2013, 10:58:04 AM »

I had a porposing problem too, then I added a ride plate and shoe. Sarted out at 0* on ride plate and now it sits at .75*-1* down, porpose all gone. The trim-a-steps were really down (5*+) when I got the boat, now they are at 0*. If they weren't already there, I wouldn't have put them on. This maybe speed dependent too. At how fast is the porpose?

Hope this helps
Daniel

« **Reply #2 on:** February 03, 2013, 11:09:00 AM »

You talking about droping the rear of ride plate down a little ?
Speed ....25-40 probably . middle range speeds . Hammered down she smooth out for ya

« **Reply #3 on:** February 03, 2013, 12:17:41 PM »

Yeah, down a little, mine porposed at 30 mph+ and kept getting worse near 50. now its flat as a board to just below 60 mph (thats all she's got). this is an open bow too.

Daniel

« **Reply #4 on:** February 03, 2013, 12:39:31 PM »

Im not sure if my ride plate will allow me to drop in rear . Im at work . Can't look at it . lol

« **Reply #5 on:** February 03, 2013, 12:48:13 PM »

Only pic i have of that area . lol

« **Reply #6 on:** February 03, 2013, 01:46:31 PM »

Looks like its 'up' from 0*, but hard to tell from that pic.. I used a 4' level on the bottom to start at 0*. you might have to add shims between the cradle and ride plate.

Daniel

« **Reply #7 on:** February 03, 2013, 01:52:19 PM »

Ah ha ! That's a good idea ! I got her stored . As it's chilly in N.Texas right now . Gonna go get her this week and try and see what i can do w it . i know the front of it bolts flush with rear pick up grate of pump

« **Reply #8 on:** February 04, 2013, 10:58:08 AM »

I have a set of those tabs

« **Reply #9 on:** February 04, 2013, 11:18:13 AM »

Are you running them ? Or storing them

« **Reply #10 on:** February 04, 2013, 07:15:45 PM »

You can also shim down using nozzle wedges, I started with 4deg and them shimed my ride plate down and propose problem is gone

« **Reply #11 on:** February 04, 2013, 07:22:07 PM »

Different set up
But here is how mine is set up
I also have a 4deg wedge, but its not shown in the pic

« **Reply #12 on:** February 04, 2013, 08:15:58 PM »

That looks just like mine all but the fact it looks as if you have some angle on your ride plate . I've heard about wedge before but someone correct me if im wrong here but doesnt wedge place more upward angle on your thrust . Giving you the capability of taller roost ? I mean after all i have a place diverter and can play w nozzle angles . It's just a lot of work on the water to try and make her ride right . Lots of playin w trim angle and throttle . WFO and 3/4 to full roost it acts good . But that's a good way to keep Opec in business . Can't ski behind her ! Or wakeboard . Hell ...or pull kids on tube . I was told to try takin off droop snoot ....?

« **Reply #13 on:** February 04, 2013, 08:20:53 PM »

I have my wedge set to angle down, thick side up to give my nozzle more down angle

« **Reply #14 on:** February 04, 2013, 08:21:33 PM »

I guess the wedge can go the other way ....depends on placement

« **Reply #15 on:** February 04, 2013, 08:23:56 PM »

Quote from: gaston langston on February 04, 2013, 08:21:33 PM

I guess the wedge can go the other way ....depends on placement

Yea, they can go either way. And I believe they start at 2deg up to 8deg sizes

« **Reply #16 on:** February 04, 2013, 08:24:48 PM »

Gotcha . Loose much roostability ? Im not all concerned w that but it looks good when ya want it

« **Reply #17 on:** February 04, 2013, 08:28:29 PM »

Don't lose that much, I believe the droop already has 4deg of up angle built into it, so if you put a 4deg on, it will be back to zero, I'm very happy with the amount of roost my boat shoots

« **Reply #18 on:** February 04, 2013, 08:35:10 PM »

Yea . im almost positive it's got 4° outa the box . I may try to zero it out if i cant get it by shimming the ride plate . I got a buddy w a glastron carlson using those step n trims . He loves them. haha . Dono . I can only find one on ebay . Takes two tho $:-\$

« **Reply #19 on:** February 04, 2013, 08:37:52 PM »

Feedback is valued my boating family . Thank you all

« **Reply #20 on:** February 04, 2013, 08:45:10 PM »

Roost is good when ya want it . Not shakin up the ice chest is good too. lol

« **Reply #21 on:** February 04, 2013, 11:01:38 PM »

http://inlandempire.craigslist.org/boa/3584464465.html

hit that guy up... it looks like theres one on that cracked mini boat. sure he would take a couple bucks for it.

« **Reply #22 on:** February 13, 2013, 11:29:40 PM »

http://losangeles.craigslist.org/lac/boa/3589961805.html

« **Reply #23 on:** February 14, 2013, 03:54:18 AM »

Thank you !

gaston langston

mash on it

gaston langston

mash on it

gaston langston

gaston langston

mash on it

gaston langston

78centurian

gaston langston

uncleBOBBY

uncleBOBBY

gaston langston

uncleBOBBY

gaston langston

uncleBOBBY

gaston langston

uncleBOBBY

gaston langston

gaston langston

gaston langston

ka0tyk

ka0tyk

gaston langston