I'm done with jet boats so I'm cleaning house. Heading from Fresno down to Long Beach this weekend (Aug 6th, sprint boat races), so if you want/need anything lets meet up and save the shipping. If you need shipping, wait till next week and see whats left.
Race is over so now everything is + shipping. Thank you to everyone that showed up to get their parts. 100% of the parts people put "on hold" where picked up, not one single person flaked.
If you don't like the prices, make an offer. Best to just call me, Jeff 559-270-1162
Brand new, place diverter with "FTN" nozzle, blue insert and nice used handle (no cable). Diverter has only been out of the box to take pics, I bought it new. Diverter alone was over $450. How about
$400 with the handle.
SOLD 
My good pump stuff. Berk suction housing, Low profile "R" style intake (uses standard loaders) with a flat shoe, Polished and worked "G" bowl (drilled and tapped for a rideplate cradle), Intake has been matched/blended to the intake and smoother all the way to the impeller area, even the hand hole cover has been smoothed, blended and the huge ugly gaps filled. Cover is still removable. All for
$400, you cant buy a low pro intake for that. A great start to build that "Bad AZZ" pump.
SOLDAlso available..
Polished Berk droop. $200
Long drive like (set back pumps). $50
Ride plate cradle. $20
SOLD Old standard nozzle adapter, pretty ugly lots of paint on it. LOL Make offer
Berk JB pump core, flat keel intake with a new blank shoe and rideplate. Needs a shaft, impeller, and kit. $250
SOLD
Stringer to stringer throttle pedal. Pedal can be moved anywhere across the bar and even adjusts for side to side tilt. Use it with normal seating or center steer set ups. Made by Nicson, not some home made junk. Will fit up to 26 1/2" between stringers, or cut it down for narrower stringers. Comes with the cable. $300.
NICE chrome exhaust tips, 2 1/2" ID. need new flaps. $50
On the right, set of BBC plates and pump brace. Two piece front mount, flywheel cover is not a "full cover" it mounts using spacers off the motor plate and just covers the rear. Only have 3 or the 6 spacers, so you need to make 3 more (small round spacers sitting above the cover in the pic). Plates are 23 1/2" wide. Raw finish but have all the edges rounded/radius. $
200 ?
SOLDOn the left, two more covers and some sort of two piece drive line cover that mounts to one of them. These are raw cut/unfinished pieces. $ 40 per cover and $20 for the D/L cover ?
All SOLD
Two sets of 2 piece BBC front mounts. These also cover the water inlets on the block. Drill and tap the plate at the water ports and run your hoses to the plate. No need for extra waster inlet adapters. $40 each
SOLD
SBC cast mounts, they are UGLY, covered with scratches etc. $40
SOLD BBC logs, same UGLY scratched condition. One sais Glenwood on the flange the other sais nothing, but they look the same ?? $ 20
SOLD Two transom adapters, one angled, one flat. $ 10 each
SOLD HallCraft throttle pedal, stringer mount, not pretty but should clean up. $40
Aluminum tanks with brackets, About 52" X 8". $
200 SOLD Two piece standard length Driveline. $40
SOLD
Ok these brackets are for mounting an alternator to the front of the pump. Bolt on over the front bearing cap. Raw cut finish. Use a turn buckle to adjust the alt and you get to figure out how to create a pulley. I have 5 of them. $10 each and you get hours of fun being creative.
2 SOLD 3 still available 
5 of these too. Simple little alternator adjustor brackets for rail kits/whatever. Raw cut finish. $10 each
All SOLD
4 header water lines, they all look different, most have at least one bad fitting, $1 for all of them.
SOLD
Fiberglas buckets and bench. Buckets are 20" wide at the widest point and bench is 40" wide at the widest point. Both are about 15" high. Bench was narrowed to this width. Glass work was done about 8 yrs ago and shows no issues. These are a thick/heavy/strong set of seats sprayed with black high fill primer, ready for you to paint your color. $ 200
SOLD
Dooley BBC jet pan. Its nasty but solid. Has surface rust inside, so it will need a good cleaning/blasting. Comes with the tray that bots to the main caps and a few of the bolts/studs to use just so you can get the right new bolt/studs. Do not use these old nasty ones. $ 100
SOLD
Really REALLY nice set of BBF Rewarder twisty headers with water lines. NO dents, NO heat discoloration past the water lines, NO rust on the flanges, NO rust in the tubes, only some very slight surface rust between the primary tubes right where they merge into the collectors. 2 1/4" OD primaries, 4" OD collectors. $ 600 ?
Dual EGT gauge with sensors. $ 125
pending I searched all over looking for a new one like this to figure a price, the ONLY one I could find like this was for aircraft and was $325.
Autometer bulb type warning light with oil pressure sender. $ 25
Left foot pedal (foot rest). Wont polish, must be clear coated. All other stuff in this pic is sold $ 75
If you want some cheap seats and don't care if your friends, wife/girlfriend, and everybody else laughs at you. I've got a deal for you !!! They even have nice TALL backs so your super fast boat doesn't break your back in half with its awesome acceleration like it would with some low back "boat" seat. They are made from light weight space age fiberglass with special vinyl covers, and even have a very small amount of padding. What will they think of next ? These will definitely add at least 10 MPH to your boat. I can even finance these seats !! All it takes to make them yours is $ 20 down (in cash) and then I don't care if you ever make another payment. If any spiders, ants, or any of Gods little creatures crawl out of them when you get them home, they are yours free with the purchase.
