Houston I have a problem...

« **on:** February 24, 2009, 07:01:32 PM »

I bought some tt headers, and when I put them up against my original exhaust , looked like NO problem

, when I took one side off, and put a couple of bolts in the header, I have a major line up prob from where the header lands to where the exhaust tip comes in from the transom

any ideas guys

« **Reply #1 on:** February 24, 2009, 07:05:46 PM »

Mark flex hose rex marine.

« **Reply #2 on:** February 24, 2009, 07:09:03 PM »

Take them back to the jackass that sold them to you and put them in his ass!

KIDDING! The hose that Rex or anyone else sells will have enough flex in it to make that offset with no problems. Make damn sure you have the plumbing 100% CORRECT for that setup, you'll only get one chance................

« **Reply #3 on:** February 24, 2009, 07:14:59 PM »

Hey Brian ya think they might fit up there

I will check the flex hose out. My only concern is that I will have a downward shaped U going out, the same as a trap on a sink. That work on exhaust

Thanks for your input also Skip

« **Reply #4 on:** February 24, 2009, 07:32:46 PM »

hey...those are familiar!

Reid

« **Reply #5 on:** February 24, 2009, 07:43:08 PM »

You recognize them Reid

« **Reply #6 on:** February 24, 2009, 07:44:55 PM »

lol slightly...make sure to post a pics of the finished install...i wanna see those babies! good luck brutha.

« **Reply #7 on:** February 24, 2009, 07:53:41 PM »

Quote from: LBsuperjet on February 24, 2009, 07:32:46 PM

hey...those are familiar!

Reid

yup sure do

« **Reply #8 on:** February 24, 2009, 08:35:45 PM »

whore headers

« **Reply #9 on:** February 24, 2009, 08:38:05 PM »

Ok so now that everyone is familiar with these (sounds like a family get together)

What about my concern that there is too much of a down loop on he exhaust

« **Reply #10 on:** February 24, 2009, 08:50:34 PM »

Mark on my dads Eliminator i got the flex hose shape like an S just bend that shit

« **Reply #11 on:** February 24, 2009, 09:07:33 PM »

76 Nordic , call me I'll help you figure it out ! Tom

« **Reply #12 on:** February 24, 2009, 09:24:53 PM »

Looks sort of like you be needin some angled tips

, The ones I picked up for my Carrera are set up to be angled out of the transom to meet the exhaust manifolds... Good luck!

GT

« **Reply #13 on:** February 24, 2009, 09:53:36 PM »

Thanks guys will give ya a holler tommorrow Tom

« **Reply #14 on:** February 24, 2009, 10:11:19 PM »

Quote from: 76NORDIC on February 24, 2009, 09:53:36 PM

Thanks guys will give ya a holler tommorrow Tom

Call my cell ,check pms Tom

« **Reply #15 on:** February 27, 2009, 10:10:25 AM »

Hey Tom did ya get the pics I sent last nite

« **Reply #16 on:** February 27, 2009, 10:26:18 AM »

How did this work out? I don't think the rex hose has much "flex" to it. I put a tall block in and just that made it a pain.

« **Reply #17 on:** February 27, 2009, 11:23:03 AM »

Hasnt been taken care of yet, and I wasnt going the Rex route, wanted to use Tom cause I,m sure he has run across this before, and wont sell me crap I dont need, also think I will prolly need different tips, but not sure, Tom will figure it out. Will post pics when all is said and done

« **Reply #18 on:** February 27, 2009, 11:44:38 AM »

X 2

....Tom will fix the prob

« **Reply #19 on:** April 09, 2009, 08:34:05 PM »

Quote from: 76NORDIC on February 27, 2009, 11:23:03 AM

Hasnt been taken care of yet, and I wasnt going the Rex route, wanted to use Tom cause I,m sure he has run across this before, and wont sell me crap I dont need, also think I will prolly need different tips, but not sure, Tom will figure it out. Will post pics when all is said and done

Mark is the boat ready.

« **Reply #20 on:** April 09, 2009, 11:28:19 PM »

bring it to blythe i will help ya fix it. lol.

ya that rubber exhaust hose should work just fine. you could also mod your tips and put a little angle on them to meet your headers. that is what i did to mine

« **Reply #21 on:** April 09, 2009, 11:38:53 PM »

this is how I fixed my problem!

« **Reply #22 on:** April 09, 2009, 11:40:27 PM »

Quote from: RedSnapperSlapper on April 09, 2009, 11:38:53 PM

this is how I fixed my problem!

The Beave told me about that, awsome job, that looks badass...Mad skills is all I gotta say.

GT

« **Reply #23 on:** April 10, 2009, 05:57:51 AM »

Quote from: AQUAHOLIC on April 09, 2009, 11:28:19 PM

bring it to blythe i will help ya fix it. lol.

ya that rubber exhaust hose should work just fine. you could also mod your tips and put a little angle on them to meet your headers. that is what i did to mine

Hope this isn't a current pic, your missing the bottom bolt for the exhaust flange and a coil wire

« **Reply #24 on:** May 14, 2009, 07:47:49 AM »

Brian I will be working on it this weekend, been workin on the trailer alot. Finally finished it and took it back out to my storage at park Moabi

76NORDIC

BOOST

Luckie Stiff

76NORDIC

LBsuperjet

76NORDIC

LBsuperjet

Ralph Brunt

BOOST

76NORDIC

BOOST

jet boat performance

GT Jets

76NORDIC

jet boat performance

76NORDIC

SLCKREG

76NORDIC

enginedoctor

BOOST

AQUAHOLIC

RedSnapperSlapper

GT Jets

crewchief22

76NORDIC