454

« **on:** December 14, 2008, 08:08:14 PM »

454 with pan, valve covers, intake, and a holley carb for $1000. Turns over nice and smooth and has compression. Stock motor with hyd cam. Would make a good ski boat or cruiser motor. 2 bolt cast crank and pistons.

Also have a stock 454 rotating assembly, std bore, pistons, rods, and std crank. Good shape and ready to run. $300 obo

« **Reply #1 on:** December 14, 2008, 08:25:00 PM »

that is actually a quite handsom motor right there...id love to swoop it up if i could right now...should sell quick.

Reid

« **Reply #2 on:** December 25, 2008, 01:13:55 PM »

Still got it...... Ok here we go, 750 cash for the motor, 200 for the rotating assembly..... I want this stuff out of my way

Somebody has to need this stuff for a winter project....

« **Reply #3 on:** December 25, 2008, 01:30:00 PM »

hey River, Mark 4, Gen 5/6 motor?

thx
Poverty

« **Reply #4 on:** December 26, 2008, 10:18:25 AM »

Sorry, should have posted that.... Mark IV .... Looks to be in decent shape... I wouldn't drop it in a race boat and go roundy round endurance racing without going thru it, but should be ok for a river/lake deal. Like I said, it's a stock comp hyd cam deal so it's only good to about 5k, but can't beat the price!!!! Includes a double pumper Holley and the manifold... Not bad for $750

« **Reply #5 on:** December 26, 2008, 10:25:21 AM »

sounds like a sweet deal

« **Reply #6 on:** December 27, 2008, 06:12:55 PM »

Give ya $750 worth of detailing Gift Certificates?

?Mark(SoCal Detail)

« **Reply #7 on:** December 28, 2008, 09:39:30 AM »

will you take an olds 455 as a trade??? $:-\$ i'm looking to convert to a chevy like beaver

« **Reply #8 on:** December 28, 2008, 09:46:55 AM »

Quote from: JWBOYER21 on December 28, 2008, 09:39:30 AM

will you take an olds 455 as a trade??? $:-\$ i'm looking to convert to a chevy like beaver

HA HA HA HA HA

I don't think that's gonna happen

« **Reply #9 on:** December 28, 2008, 09:54:22 AM »

Quote from: GlassCutter on December 28, 2008, 09:46:55 AM

HA HA HA HA HA I don't think that's gonna happen

i know, i was thinking kinda like a down payment

« **Reply #10 on:** December 28, 2008, 12:12:46 PM »

Trade you for a complete 12JCA Berkeley pump! I have a couple different intakes (round and flat) TA the whole deal, it's fresh with a newer bearing, impeller (aluminum A), packing and grease seals, came from my boat and has like one season on it (under 40 hours).

Otherewise that is a sweet deal, cannot believe its still there..

« **Reply #11 on:** December 28, 2008, 12:27:16 PM »

Would you be interested in a 1960 Savage Model 99f .308 rifle for the 454?

Original and near excellent condition.

« **Reply #12 on:** January 14, 2009, 09:46:58 PM »

Sorry, not looking for any trades right now, got enough stuff as it is!!!

« **Reply #13 on:** January 29, 2009, 09:36:24 PM »

PM sent.
Jason send me your number. I am very interested.

« **Reply #14 on:** February 11, 2009, 01:53:49 AM »

Is this engine still for sale??

« **Reply #15 on:** May 31, 2009, 03:32:25 PM »

how about $750 cash but looking for mounting hardware?

« **Reply #16 on:** May 31, 2009, 08:58:41 PM »

Sorry guys, didn't check this post for a while, as you can see. Motor is still here if anybody needs one, give me a call. Jason 951-675-9249

« **Reply #17 on:** June 08, 2009, 07:47:16 AM »

Complete motor sold, the other one is still available. Lowered price to $250

« **Reply #18 on:** June 08, 2009, 07:50:00 AM »

Ok I'm mixing posts

The rotating assembly is now $150. The other post includes a block, heads, rotating assembly, pan, intake manifold, etc. It's a .020 over two bolt ready to be cleaned and reassembled with new gaskets and bearings. That one is $250. I'm ready to get this crap outa my garage!

« **Reply #19 on:** June 08, 2009, 09:20:13 AM »

Thanks Jason for the motor. I pulled the rod bearings of to inspect and they looked good! I can also still see the hone marks in the cylinder walls. This must have been freshened up not too long ago! I already have plans for it. My dad has a set off 990 heads that have work done to them, and a nice roller cam, plus I have a few other goodies too.

« **Reply #20 on:** June 08, 2009, 01:18:02 PM »

I am interested. PM Sent.

« **Reply #21 on:** June 08, 2009, 03:21:00 PM »

Great, nice to meet ya yesterday Nick! Good luck with it.... The other motor sold as well to a future circle boat hall of famer.

The goal is to have as many of my parts in the boats on these boards as I can so that I'm alway's gauranteed a ride at the river!! God knows I have no time to work on my own stuff! LOL

« **Reply #22 on:** June 08, 2009, 08:51:54 PM »

Thanks Jason. After blowing up the motor in the Advantage at Puddingstone, I need to start getting something together for it.
One day soon the family is going to ask what happen to their river trips.

Tio, after I go thru things and decide which parts i'm going to use, i'll let you know what I have to sell.

River Dad

LBsuperjet

River Dad

povertyjet

River Dad

bkplesh

SoCal Detail

JWBOYER21

GlassCutter

JWBOYER21

GT Jets

crewchief22

River Dad

koyota93

theskitzofrantic

skooter55

River Dad

River Dad

River Dad

MADSKILLZ

Tio Pancho

River Dad

76 Bonneville