Null


Pages: [1]

Nordie

  • Karma: +13/-0
Impeller Nut
« on: February 03, 2011, 04:01:45 PM »
You guys made it sound like a bitch...with some rod busting tools no freaking problem...a 15" cresent wrench attatched to a 3 prong hickey bar...a hickey bar is what i use at work to bend rebar...followed by a 2 foot flathead screwdriver to hold the flywheel...one little push and right off
« Last Edit: February 03, 2011, 06:03:05 PM by Nordie »
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party


If im not posting..I'm pooping!

ka0tyk

  • Karma: +30/-0
Re: Impeller Nut
« Reply #1 on: February 03, 2011, 04:08:18 PM »
seems like an impact with an extension wouldve been a hell of a lot less work.
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

Nordie

  • Karma: +13/-0
Re: Impeller Nut
« Reply #2 on: February 03, 2011, 05:25:10 PM »
Fock the extension i would have needed a 5 or 6 inch deep socket...thanks for the suggestion, but an extension would have been deemed useless!
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party


If im not posting..I'm pooping!

Brad @ SCJB

  • Karma: +255/-0
Re: Impeller Nut
« Reply #3 on: February 03, 2011, 05:53:05 PM »
i seen one that one that came off finger tight  :screwy:
Logged
  • Boat #1: 1978 Liberty
  • Boat #2: 1982 Eliminator Sprint
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

TJS Nordic

  • Karma: +2/-0
Re: Impeller Nut
« Reply #4 on: February 11, 2011, 07:44:00 PM »
I know you got it off but for future buy a cheapo socket cut it and weld a piece of pipe in it. Took about 1/2 hour to make. Got it cheap at NAPA for 10 bucks.
T.J.
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

Nordie

  • Karma: +13/-0
Re: Impeller Nut
« Reply #5 on: February 12, 2011, 07:51:18 AM »
then i half to buy a welder too
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party


If im not posting..I'm pooping!

Brendella Pickle

  • Karma: +0/-0
Re: Impeller Nut
« Reply #6 on: February 12, 2011, 09:31:21 AM »
Quote from: Nordie on February 12, 2011, 07:51:18 AM
then i half to buy a welder too

I have a welder. LEt's make some tools... bring it
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

77GT

  • Karma: +1/-0
Re: Impeller Nut
« Reply #7 on: February 12, 2011, 11:56:44 AM »
I just made a deep socket to remove the impeller nut on my pump.

What does your impeller puller look like?
Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party
SAM in L.A., thats Lower Alabama
77 GT Boats

TJS Nordic

  • Karma: +2/-0
Re: Impeller Nut
« Reply #8 on: February 12, 2011, 12:49:27 PM »
Puller

Logged
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

GT Jets

  • Karma: +192/-0
Re: Impeller Nut
« Reply #9 on: February 12, 2011, 01:20:27 PM »
Quote from: TJS Nordic on February 12, 2011, 12:49:27 PM
Puller



Dude, do you buy any tools?  LMAO.    Nice, I thought I was bad, I should get my camera out and show some of my "special tools"....

The coolest one I have seen (garage made) was an impeller nut socket/impeller puller combo, those Hoosiers are out of control. :sly:

Worked slicker than owl shit too... :thumbup: :thumbup:

GT
Logged
  • Boat #1: 1992 Carrera 20.5 Elite (I/O bitches)
  • Boat #2: 19' Bubble deck Jet BBC Berkeley
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party
Quote from: Brad @ SoCalJetBoats.com on December 22, 2009, 07:40:31 PM
If i get some free time tonight at work, ill play with it and post it for everyone to see.

Quote from: IRRebel on June 11, 2011, 07:30:45 PM
Time to man up and yank it John!  :banghead:
Ray
Pages: [1]
 


Null

SMFPacks CMS 1.0.3 © 2026