Null


Pages: [1]

jyeager

  • Karma: +62/-0
Dimarco 18 hardware set up
« on: June 24, 2014, 09:00:14 PM »
Alright boys, need some advice of where to start with the hardware with the dimarco. I've only done tunnels so.... I was thinking nozzle at 6*up and rideplate at 4* up. Shoe 1/8th above keel and the loader ramps are 1/2 inch above keel.

What do you guys think?


Sent from my iPhone using SoCalJetBoats mobile app
« Last Edit: June 24, 2014, 09:02:32 PM by jyeager »
Logged
  • Boat #1: Southwind Tunnel Dragster 19
  • Boat #2: DiMarco18 V-Bottom
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

Beaveretriever

  • Karma: +34/-0
Re: Dimarco 18 hardware set up
« Reply #1 on: June 24, 2014, 09:22:07 PM »
Seems like alot od nozzle angle. I would start at 4* and run the shoe even

Sent from my SAMSUNG-SGH-I747 using SoCal Jet Boats mobile app

Logged
  • Boat #1: 1981 Eliminator Daytona 19' Jet
  • Boat #2: 2003 22' Placecraft Deck boat
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

Brad @ SCJB

  • Karma: +255/-0
Re: Dimarco 18 hardware set up
« Reply #2 on: June 24, 2014, 09:30:36 PM »
rideplate at 3 degrees up
nozzle 3-4 degrees up from keel. I assume your intake is 4 degrees down? ....so 6-7degrees up from pump angle.

not sure about shoe and loader, but i'd start with the 2 above and work on the 2nd 2 after that.
Logged
  • Boat #1: 1978 Liberty
  • Boat #2: 1982 Eliminator Sprint
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

jyeager

  • Karma: +62/-0
Dimarco 18 hardware set up
« Reply #3 on: June 24, 2014, 09:33:56 PM »
Quote from: Brad @ SCJB on June 24, 2014, 09:30:36 PM
rideplate at 3 degrees up
nozzle 3-4 degrees up from keel. I assume your intake is 4 degrees down? ....so 6-7degrees up from pump angle.

not sure about shoe and loader, but i'd start with the 2 above and work on the 2nd 2 after that.

3 up? Sounds like not a lot of up for the ride plate. I'll try that and work from there. Yeah intake is in at 4.1 and 3* back cut shoe. Also the nozzle is angle is in relation from keel and the intake


Sent from my iPhone using SoCalJetBoats mobile app
« Last Edit: June 24, 2014, 09:38:08 PM by jyeager »
Logged
  • Boat #1: Southwind Tunnel Dragster 19
  • Boat #2: DiMarco18 V-Bottom
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party

jyeager

  • Karma: +62/-0
Dimarco 18 hardware set up
« Reply #4 on: June 24, 2014, 09:36:57 PM »
A
Logged
  • Boat #1: Southwind Tunnel Dragster 19
  • Boat #2: DiMarco18 V-Bottom
  • Like
    Dislike
    Love
    HaHa
    Angry
    Surprise
    Sad
    Party
Pages: [1]
 


Null

SMFPacks CMS 1.0.3 © 2026