What did you do to your boat today?

« **Reply #3450 on:** March 03, 2016, 05:08:01 PM »

The Chariot got her a makeover today one down one to go.

Sent from my iPhone using SoCal Jet Boats

« **Reply #3451 on:** March 03, 2016, 10:25:00 PM »

Primed and ready to fire. Tomorrow all the sweat blood and years come down to a single turn of the key

« **Reply #3452 on:** March 04, 2016, 07:25:49 AM »

Good luck! I feel your anxious pain. Goin to be in the same situation soon. See if it all pays off!

« **Reply #3453 on:** March 04, 2016, 07:04:45 PM »

Picked up my pump from GS Marine can't wait to run this thing now. Full rebuild, detailed impeller, inducer, fully detailed split bowl, HPH mini droop, hydraulic Place diverter, and fresh powder!!

Sent from my iPhone using SoCal Jet Boats

« **Reply #3454 on:** March 04, 2016, 07:34:38 PM »

I got a new driver for the boat, he's only 4 but is good at waving with his head thrown back.

« **Reply #3455 on:** March 04, 2016, 09:51:18 PM »

Ran her for a little bit making sure she's ready for spring.
Purrrring like a kitten

« **Reply #3456 on:** March 05, 2016, 04:10:08 AM »

I'm slapping heads on. Figure'n witch head studs go where. 3 different lengths . Another day in paradise.

« **Reply #3457 on:** March 05, 2016, 12:42:16 PM »

Lookin good!

« **Reply #3458 on:** March 05, 2016, 07:54:42 PM »

Thank you sir!

« **Reply #3459 on:** March 05, 2016, 09:16:31 PM »

Flex plate and oil pan gasket

Sent from my iPhone using SoCal Jet Boats

« **Reply #3460 on:** March 05, 2016, 09:45:57 PM »

Found out I need a flex plate and a starter. Fun stuff

« **Reply #3461 on:** March 06, 2016, 11:48:02 AM »

Does anyone use this? Came up on a bunch of it at work and want to use t for my npt-an fittings for fuel and water

Sent from my iPhone using SoCal Jet Boats

« **Reply #3462 on:** March 06, 2016, 12:19:31 PM »

Quote from: Bunger on March 06, 2016, 11:48:02 AM

Does anyone use this? Came up on a bunch of it at work and want to use t for my npt-an fittings for fuel and water

Sent from my iPhone using SoCal Jet Boats

I like it for the NPT fittings. Don't use it on the AN, the seal is created by the wedge affect as the 37-degree tapers clamped together. The threads on AN fittings are for retention only. I do use anti-seize only on the threads of the AN fittings.

« **Reply #3463 on:** March 06, 2016, 12:20:49 PM »

Quote from: Flusher on March 06, 2016, 12:19:31 PM

I like it for the NPT fittings. Don't use it on the AN, the seal is created by the wedge affect as the 37-degree tapers clamped together. The threads on AN fittings are for retention only. I do use anti-seize only on the threads of the AN fittings.

Oh I know not the use it on the an itself just for the npt end of the adapter. I should be okay to use it for fuel tho correct?

Sent from my iPhone using Tapatalk

« **Reply #3464 on:** March 06, 2016, 12:39:36 PM »

Yes that stuff works great been using it for 10 years on all my pipe thread fittings.

Sent from my iPhone using SoCal Jet Boats

« **Reply #3465 on:** March 06, 2016, 03:17:20 PM »

Well this bitch is ready to drop in the boat. Probably next weekend.

« **Reply #3466 on:** March 08, 2016, 09:10:54 AM »

Installed Imco tanks with new hardware installed wema fuel sending unit now trying to figure out how I should wire the boat. I want to use a relay for the place diverted pump and do steering wheel push buttons to actuate it. Any suggestions on wiring

Sent from my iPhone using Tapatalk

« **Reply #3467 on:** March 08, 2016, 09:13:12 AM »

Sealed up the aluminum plates for the transom that I built couldn't get the inside of the transom pretty like I had hoped, being that it's a set back pump it's quite tight in there.

Sent from my iPhone using Tapatalk

« **Reply #3468 on:** March 08, 2016, 09:14:38 AM »

Quote from: Bunger on March 06, 2016, 11:48:02 AM

Does anyone use this? Came up on a bunch of it at work and want to use t for my npt-an fittings for fuel and water

Sent from my iPhone using SoCal Jet Boats

I use that on all the hydraulic fittings at work
Not sure how well it would work with fuel

Sent from my iPhone using Tapatalk

« **Reply #3469 on:** March 08, 2016, 06:09:09 PM »

Removed oxidation. Just need flexplate and starter now

« **Reply #3470 on:** March 09, 2016, 04:29:42 AM »

Got oil cooler ready to go into the boat 😁

Sent from my iPhone using SoCal Jet Boats

« **Reply #3471 on:** March 09, 2016, 06:47:21 AM »

Quote from: Outlawmayhem on March 03, 2016, 09:30:24 AM

Shit I dont even wanna know what you're selling that for. I already know I can't afford it. I spent time restoring those over the summer 2 years ago. I want one so bad.

119 is what she is going for.

Sent from my iPhone using Tapatalk

« **Reply #3472 on:** March 09, 2016, 04:07:42 PM »

Picked this up in old town orange at one of the antique stores. Thought it was fitting for the living room.

Started to gut old harness and going to make a new one and bench test my old gauges.

Sent from my iPhone using Tapatalk

« **Reply #3473 on:** March 09, 2016, 04:42:01 PM »

1969? Wow!

« **Reply #3474 on:** March 09, 2016, 08:06:44 PM »

How to Noiseproof a Room

And

Quick Guide to Chain Saws

Hmmmmmm

88 Baker

SomeThingWilder

FordLover

Oliver1421

YellowJacket

455Whiskey Gal

vwagon13

FordLover

vwagon13

randog

MerikaRogers

Bunger

Flusher

Bunger

Oliver1421

FordLover

willowvalley

willowvalley

willowvalley

MerikaRogers

Bunger

willowvalley

willowvalley

FordLover

Flusher