Eliminator

« **Reply #75 on:** February 10, 2009, 06:53:43 PM »

Seems your FIL has a habitual problem getting paperwork right 2sav, lol.

Ray

« **Reply #76 on:** February 10, 2009, 07:28:29 PM »

Quote from: Brad @ SoCalJetBoats.com on February 10, 2009, 06:47:57 PM

unless this is something new....i have to disagree....i've done it before.

I don't know how long it has been in affect, but the California privacy laws limit how much information can be given without authorization.

The chassis manufacturer that we do warranty work for has recently sent out another round of recall notices to clients that they did not have complete information for. I had been told the last time they sent out notices that they had to get help from the NHTSA or a Court order to get the information needed.

« **Reply #77 on:** February 11, 2009, 06:23:52 PM »

Pulled the pan today

This is the oil pick up

And this is the thick substance in the pan

i think now i know why it lost oil pressure so quickly, there was silicon in the pick up aswell . I have not checked the bearings yet , but this will be my builder for my next engine

« **Reply #78 on:** February 11, 2009, 07:18:38 PM »

Houston I think we have a problem. That ain't good.

« **Reply #79 on:** February 12, 2009, 10:57:21 PM »

So THAT"S how they make metallic paint! Always wondered..... lol

Honestly though, If you filter all that out through a coffee filter (COuld take months), I'll bet you get enough material outta that to cast a new piston.........

Ray

« **Reply #80 on:** February 13, 2009, 12:21:53 AM »

Quote from: IRRebel on February 12, 2009, 10:57:21 PM

So THAT"S how they make metallic paint! Always wondered..... lol

Honestly though, If you filter all that out through a coffee filter (COuld take months), I'll bet you get enough material outta that to cast a new piston.........

Ray

Sad part is, there is probably very little metal in it, that is what we call a Banana milkshake

that is what you get when you have water in the oil and the engine runs, looks like a 6 month olds diaper after eating four bowl of cream of wheat

Don't ask!

I will make a recomendation on the best way to clean it up though...Use a heat gun and the water will start to separate out due to the different boiling points, should take about an hour or two, so grab a couple of beers

GT

« **Reply #81 on:** February 13, 2009, 02:07:35 AM »

That engine is completely torn down and waiting for me to rebuild it as my next Ford KILLER

We will have a motor from JBP here on saturday to replace it with (turn key engine )

Then i can start working on my boat

Eliminator is all cleaned up and ready to go again... Man he owes me BIG TIME. this is how im spending my vacation.
working On his boat

there was a half inch of grease in the bilge i had to scrub out , not fun.

this is the only pic i got of all the shit that is fuked on this engine. top ring #6 piston.

Piston was starting to melt where the break was. this engine was a time bomb...

« **Reply #82 on:** February 13, 2009, 06:58:04 AM »

That engine is completely torn down and waiting for me to rebuild it as my next Ford KILLER

you don't even have A running ford killer yet

, lets not get ahead of ourselves there buddy, one step at a time, finish the boat, then sneak up and wip some ford ass

« **Reply #83 on:** February 13, 2009, 07:06:28 AM »

Quote from: FORKEDUP on February 13, 2009, 06:58:04 AM

That engine is completely torn down and waiting for me to rebuild it as my next Ford KILLER

you don't even have A running ford killer yet , lets not get ahead of ourselves there buddy, one step at a time, finish the boat, then sneak up and wip some ford ass

Your too late Josh allready gave me shit for that...

What i meant to say is , i will be building a engine slowly after the boat is running and not before.....

I will be with you boys this summer ON THE WATER IN My boat

« **Reply #84 on:** February 13, 2009, 12:09:41 PM »

The March Mead trip is coming soon, get together and bring it out

« **Reply #85 on:** February 14, 2009, 07:45:13 PM »

Quote from: crewchief22 on February 13, 2009, 12:09:41 PM

The March Mead trip is coming soon, get together and bring it out

I might be taking the Eliminator

Look what just showed up at my doorstep, Straight from JBP

Sooooo..... Tomorrow is another full day of working on somebody elses boat, but that means im that much closer to getting mine done..( i think )
Tomorrow i change the hoses and carb, starter and drop this bitch in..

« **Reply #86 on:** February 14, 2009, 09:00:36 PM »

He's working on someone else's boat all day tomorrow and that makes him closer to having his own boat finished???

Sounds a little fishy to me.

People say you keep getting a little closer with each project to actually finishing one. Seems like if you spent as much time wrenching as you do typing these threads, you'd have all four of them done by now...

« **Reply #87 on:** February 14, 2009, 09:04:45 PM »

LOL I gotta say.....Funny shit that the newbie is already ripping on you Steve. He must be very observnet.

« **Reply #88 on:** February 14, 2009, 09:05:39 PM »

Quote from: Baja and Bust on February 14, 2009, 09:00:36 PM

Seems like if you spent as much time wrenching as you do typing these threads, you'd have all four of them done by now...

« **Reply #89 on:** February 14, 2009, 09:30:51 PM »

Well, I for one kinda agree with Steve on this one. Or at least see where his heads at. Gotta keep FIL happy, if FIL happy, G/F happy, all goes well, everybody puts out, no worries about poisoned CoCo Puffs.......etc. etc etc.... Wouldn't want to be the subject matter of the trial that sends FIL back to prison either....... Such a quagmire!!

Besides, his Beaner is the closest thing to seaworthy I've seen yet, and I've only been on the site a couple of months. even AFTER looking at all the old posts! Somebody go give this guy a hand before I take my vacation time or hire some help from the Circle K here to help him do it!

Look at the pot calling the kettle black, lol. I'm just as bad. Once my new oil pan and pickup arrive, we'll be ready to post picks of my "Udder" one as GT calls it. Should be in the water weekend after next for a test, or God unwilling, a rescue.....

Ray

« **Reply #90 on:** February 15, 2009, 06:24:41 AM »

Quote from: Baja and Bust on February 14, 2009, 09:00:36 PM

He's working on someone else's boat all day tomorrow and that makes him closer to having his own boat finished???
Sounds a little fishy to me.

Who gives a fuck on what YOU think Newbie... You don't know Shit!!!!

Quote from: Baja and Bust on February 14, 2009, 09:00:36 PM

People say you keep getting a little closer with each project to actually finishing one. Seems like if you spent as much time wrenching as you do typing these threads, you'd have all four of them done by now...

Again you dont have a clue , Are you or anyone else here helping me NO so since you are just jumping on the band wagon of " lets bash 2sav " cause he dont have a running boat yet ,Go for it AND BASH AWAY.

And to the people that have been to my pad and see the shit im going through to make EVERYONE happy this is not for you.. You understand my situation and dont shit on me for it

So now i have posted my last post just to make everyone happy for awhile..

Have a great day

« **Reply #91 on:** February 15, 2009, 06:32:55 AM »

Hi Steve!

« **Reply #92 on:** February 15, 2009, 09:03:07 AM »

Steve get the boat done so you can whip some newbie ass

« **Reply #93 on:** February 15, 2009, 09:33:49 AM »

Eeewww.........you mean whip?

« **Reply #94 on:** February 15, 2009, 11:31:19 AM »

Hey Steve.... I'm Ken... I may be new to this site but I know a lot more SHIT than you think.

My apologies though, I wasn't trying to piss you off. Just having a little fun on the boards. I see what's going on here with all your different projects and willingness to give up when you run into a snag. So forgive me for being a new member on the site. I wasn't trying to burst your bubble, just to spice things up a little bit. Ahhh, the sweet smell of success... Maybe you'll smell that smell someday.

« **Reply #95 on:** February 15, 2009, 05:50:00 PM »

Quote from: Baja and Bust on February 15, 2009, 11:31:19 AM

Hey Steve.... I'm Ken... I may be new to this site but I know a lot more SHIT than you think.

My apologies though, I wasn't trying to piss you off. Just having a little fun on the boards. I see what's going on here with all your different projects and willingness to give up when you run into a snag. So forgive me for being a new member on the site. I wasn't trying to burst your bubble, just to spice things up a little bit. Ahhh, the sweet smell of success... Maybe you'll smell that smell someday.

(willingness to give up when you run into a snag)

Please explain

Since you think you know what i do and how i do it.

I would really like to see this one..

And on with the Eliminator.

Motor is in

I spent all day on this bitch and my FIL owes me BIG TIME

I still need a few things to finish it, gaskets, carb adapter ( stock manifold )

Add some oil and put in in the river to fire this pig.. I told him after this you are on your own

well see what happens!!

Notice the new V/C's

that carb is only there to keep the dust and dirt out.. got a new one on the shelf for it..
Thanks again Tom for hooking us up.....

« **Reply #96 on:** February 15, 2009, 05:59:23 PM »

Dayum!, Somebody was a busy one today...Nice work bro...

Hope it all works the way it's supposed to...

GT

« **Reply #97 on:** February 15, 2009, 06:25:25 PM »

Great job Steve that boat keeping you busy almost done.

« **Reply #98 on:** February 15, 2009, 06:44:08 PM »

Thanks guys

I spent 8 hours straight on this pig and tomorrow I get to order more parts

Im starting to get a little stress relief from this whole deal

« **Reply #99 on:** February 15, 2009, 07:09:54 PM »

Good job 2sav, looks like your going to have a couple boats to choose from this summer.

IRRebel

crewchief22

2savage4you

GlassCutter

IRRebel

GT Jets

2savage4you

FORKEDUP

2savage4you

crewchief22

2savage4you

Baja and Bust

flytime

Luckie Stiff

IRRebel

2savage4you

Luckie Stiff

BOOST

HDriderTH

Baja and Bust

2savage4you

GT Jets

BOOST

2savage4you

propless